HY8:Concrete Open Bottom Arch: Difference between revisions
| (6 intermediate revisions by one other user not shown) | |||
| Line 9: | Line 9: | ||
The polynomial coefficients used by HY-8 were derived from a study and document prepared by Don Chase at the University of Dayton, Ohio (1999). Dr. Chase determined a different set of coefficients for culverts with different span-to-rise ratios. Con/Span culverts with a 4:1 span-to-rise ratio performed better (resulted in a lower headwater) than culverts with a 2:1 span-to-rise ratio. Because of this, separate polynomial coefficients were determined for culverts with each of these span-to-rise ratios. | The polynomial coefficients used by HY-8 were derived from a study and document prepared by Don Chase at the University of Dayton, Ohio (1999). Dr. Chase determined a different set of coefficients for culverts with different span-to-rise ratios. Con/Span culverts with a 4:1 span-to-rise ratio performed better (resulted in a lower headwater) than culverts with a 2:1 span-to-rise ratio. Because of this, separate polynomial coefficients were determined for culverts with each of these span-to-rise ratios. | ||
Dr. Chase's study determined the K, c, M, and Y NBS coefficients described in HDS-5, and these coefficients were fitted to a 5th degree polynomial equation so they can be used in HY-8. | Dr. Chase's study determined the K, c, M, and Y NBS coefficients described in HDS-5, and these coefficients were fitted to a 5th-degree polynomial equation so they can be used in HY-8. | ||
In HY-8, the 2:1 coefficients are used if the span:rise ratio is less than or equal to 3:1 and the 4:1 coefficients are used if the span:rise ratio is greater than 3:1. If the culvert | In HY-8, the 2:1 coefficients are used if the span:rise ratio is less than or equal to 3:1, and the 4:1 coefficients are used if the span:rise ratio is greater than 3:1. If the culvert being modeled has less than a 2:1 or greater than a 4:1 span-to-rise ratio, the user will see a note in HY-8 saying that the culvert is outside of the tested span-to-rise ratios. Further testing may be required to account for these large or smaller span-to-rise ratios, but it is likely that the computed headwater will be higher than the observed headwater if the span:rise ratio is greater than 4:1 and the computed headwater will be less than that observed if the span:rise ratio is less than 2:1. | ||
For information on the exact coefficients used and to view diagrams showing the different culvert wingwall configurations, see the help describing the [[ | For information on the exact coefficients used and to view diagrams showing the different culvert wingwall configurations, see the help describing the [[HY-8:Polynomial Coefficients#Table 5. Polynomial Coefficients - Concrete Open-Bottom Arch|HY-8 polynomial coefficients]]. | ||
{{HY8Main}} | {{HY8Main}} | ||
[[Category:Culvert Data|C]] | |||
[[Category:External Links]] | |||
Latest revision as of 21:45, 5 May 2020
HY-8 Version 7.3 and later has coefficients for computing inlet control depths for concrete open-bottom arch (commonly called Con/Span) culverts.
Geometric Characteristics
Con/Span culverts have unique geometric configurations, and several sizes and shapes are available. The exact coordinates used in HY-8 to compute areas and other geometric cross section parameters are available in this document. Since the culverts can be made to accommodate any required rise for a given span, HY-8 contains culvert geometry in 3-inch increments of rise.
Inlet Control Polynomial Coefficients
The polynomial coefficients used by HY-8 were derived from a study and document prepared by Don Chase at the University of Dayton, Ohio (1999). Dr. Chase determined a different set of coefficients for culverts with different span-to-rise ratios. Con/Span culverts with a 4:1 span-to-rise ratio performed better (resulted in a lower headwater) than culverts with a 2:1 span-to-rise ratio. Because of this, separate polynomial coefficients were determined for culverts with each of these span-to-rise ratios.
Dr. Chase's study determined the K, c, M, and Y NBS coefficients described in HDS-5, and these coefficients were fitted to a 5th-degree polynomial equation so they can be used in HY-8.
In HY-8, the 2:1 coefficients are used if the span:rise ratio is less than or equal to 3:1, and the 4:1 coefficients are used if the span:rise ratio is greater than 3:1. If the culvert being modeled has less than a 2:1 or greater than a 4:1 span-to-rise ratio, the user will see a note in HY-8 saying that the culvert is outside of the tested span-to-rise ratios. Further testing may be required to account for these large or smaller span-to-rise ratios, but it is likely that the computed headwater will be higher than the observed headwater if the span:rise ratio is greater than 4:1 and the computed headwater will be less than that observed if the span:rise ratio is less than 2:1.
For information on the exact coefficients used and to view diagrams showing the different culvert wingwall configurations, see the help describing the HY-8 polynomial coefficients.
