SMS:ADH SMS 13.2 and Earlier

"ADH is a state-of-the-art ADaptive Hydraulics Modeling system developed by the Coastal and Hydraulics Laboratory (CHL), ERDC, USACE, and is capable of handling both saturated and unsaturated groundwater, overland flow, three-dimensional Navier-Stokes flow, and two- or three-dimensional shallow water problems." [1]

Information about the ADH model can be found at the ADaptive Hydraulics Modeling HomePage.

Graphical Interface

Dialogs

SMS provides the capability to view and edit model parameters via dialog boxes specific to the ADH interface. The following are descriptions of important windows accessible from the ADH menu and right-click menus.

• Model Control
• Boundary Condition Assignment
• Material Properties
• Hot Start Initial Conditions
• Model Check
• Boundary Layers
• Run Model

Files

An ADH simulation is defined using three main files: mesh geometry (*.3dm), boundary conditions (*.bc), and hot start conditions (*.hot). ADH expects a 3-dimensional mesh geometry since it can solve 3D models, but SMS will only interface the 2D capabilities and will therefore only read and write 2D entities in the *.3dm file. A generic SMS mesh geometry file (*.2dm) can be used by ADH if the extension is changed to *.3dm. To facilitate handling the ADH files, SMS creates a simulation file (*.sim) which lists the individual files. Opening the *.sim will load the ADH files in SMS.

Each file is a card based text file that can be viewed and edited by a text editor (i.e. Notepad).

• Mesh geometry file (*.2dm/*.3dm)
• Boundary condition file (*.bc)
• Hot start file (*.hot)
• Boat definition file (*.bt)

Using the Model / Practical Notes

ADH uses string structures to assign properties to entities. The following table describes the relation between the string structures and SMS structures.

ADH to SMS (Reading)

ADH String Structure		SMS Structure
NDS with DB card	and only 1 node ID	Node with boundary condition (BC)
	and 2 or more node IDs	Nodestring with BC
EGS with NB card (and possibly FLX card)		Nodestring with BC (and flux output)
MDS with FLX card		Nodestring with flux output
MTS with MP cards		Material with properties

SMS to ADH (Writing)

SMS Structure			ADH String Structure
Node with BC (Dirichlet)			NDS (only 1 node ID) with DB card
Nodestring	with Natural BC	with flux output	EGS with NB and FLX cards
			EGS with NB card
	with Dirichlet BC	with flux output	NDS (2 or more node IDs) with DB card, and MDS with FLX card
			NDS (2 or more node IDs) with DB card
	with flux output		MDS with FLX card
Material with properties			MTS with MP cards

Case Studies / Sample Problems

The following ADH simulation files have been provided by CHL to test ADH and the SMS interface capabilities. Additional test cases will be posted here as the interface can successfully read, write, and run the ADH model from within SMS. SMS 10.1 Development version using ADH rev #3669 dated August 2007:

• [sms.aquaveo.com/ADH-bayousorrel.zip Bayou_Sorrel] – Uses the NB OVL and NB OTW boundary condition cards. Includes two materials on a complex mesh.
• [sms.aquaveo.com/ADH-pool5.zip Pool5] – Uses the NB OVL and NB OTW boundary condition cards. Includes two inflows with one outflow and four materials on a complex mesh.
• [sms.aquaveo.com/ADH-nb_dis.zip nb dis] – Tests the NB DIS boundary card on a straight flume.
• [sms.aquaveo.com/ADH-op_bt.zip op bt] – Tests the OP BT card which includes the vessel movement library. This test case contains a boat definition file (*.bt).
• [sms.aquaveo.com/ADH-db_lde.zip db lde] – Tests the DB LDE pressure lid card on a straight flume.
• [sms.aquaveo.com/ADH-db_ldh.zip db ldh] – Tests the DB LDH pressure lid card on a straight flume.
• [sms.aquaveo.com/ADH-db_lid.zip db lid] – Tests the DB LID pressure lid card on a straight flume.