A borehole cross section is a set of polylines and polygons that define the stratigraphy between two boreholes. A borehole cross section can be created manually or automatically.
Creation
Cross sections can be created either automatically or manually.
Automatic Creation
Cross sections can be created automatically using the Boreholes | Auto-Create Blank Cross Sections menu command. This uses a triangulation process to determine the most likely connections between boreholes. The top and/or bottom arcs of the new cross sections can be warped to match the elevation of TIN surfaces using the Snap Cross Sections to TIN dialog which appears when the Boreholes | Auto-Create Blank Cross Sections command is executed. Snapping the tops and bottoms of cross sections to TIN surfaces can also be done at any time via the Boreholes | Advanced | Snap Cross Sections to TIN menu command. Keep in mind, however, that warping the top and bottom of a cross section may interfere with the internal polygons that are defined in the cross section, so snapping to a TIN is best done before filling in the cross sections.
The
Snap Cross Sections to TIN dialog
Manual Creation
Cross sections can be created manually by using the Create Cross Section tool and clicking on boreholes.
Editing
When a borehole cross section is first created, it is made up of a set of default lines. The figure below shows a default cross section. Notice that "arcs" (polylines) have been created defining the top and bottom of the cross section and an arc (polyline) has been created for each segment in the boreholes.
Automatic Editing
The
Auto-Fill Cross Sections dialog
The Boreholes | Auto-Fill Blank Cross Sections menu command can be used to automatically fill in all existing blank cross sections. The command can use either the horizon IDs (preferred) or materials information on the boreholes.
Manual Editing
To edit a cross section manually, use the Select Cross Section tool and select a cross section. The Cross Section Editor dialog can be then opened by selecting the Cross Section Editor command from the Borehole menu while either a single or a series of cross sections selected. It is also possible to launch the Cross Section Editor dialog by double-clicking on a single cross section. The next figure shows a finished cross section.
Restrictions
GMS imposes the following restrictions on cross sections that should be kept in mind when editing:
- All polygons must be connected to boreholes
- All arcs must connect to borehole contacts
Borehole Cross Section Editor
The Cross Section Editor can be used to manually construct and view cross sections between boreholes. The Cross Section Editor in GMS 6.5 has been updated to allow for the display and editing of multiple borehole cross sections. The Cross Section Editor has a set of tools and options used to create, edit, and view the cross sections. The tools used to create the nodes, polylines, and polygons are similar to the tools available in the Map module used to create feature objects (points, arcs, and polygons). The following tables describe the tools and display options available in the Cross Section Editor.
The
Cross Section Editor dialog
Tools
| Tool |
Tool Name |
Description
|
 |
Select Tool |
Generic selection tool that selects nodes, vertices, arcs, and polygons
|
 |
Select Point/Node |
Selection tool that will only select points or nodes
|
 |
Select Vertex |
Selection tool that will only select vertices
|
 |
Select Arc |
Selection tool that will only select arcs
|
 |
Select Polygon |
Selection tool that will only select polygons
|
 |
Create Vertex |
Creates new vertices along arcs within the cross section
|
 |
Create Arc |
Creates arcs between two nodes or vertices within the cross section
|
 |
Pan |
Pans in the viewing area of the Graphics Window
|
 |
Zoom |
Magnifies or shrinks the current viewing area
|
 |
Frame All Cross Sections |
Frames to the extents of all the cross sections
|
 |
Frame Current Cross Section |
Frames to the extents of the current cross section
|
 |
Z-Magnification |
Adjusts the Z-Magnification factor to increase or decrease the graphical display along the Y (real world Z) axis, making more or less room at the top and bottom of the screen while maintaining the boreholes and cross sections in the middle of the screen
|
 |
Plot Options |
Opens the Plot Options dialog. The dialog has tools for adjusting the axes plot options, including: title, background color, font, font color, grid display, axes titles, and axes display
|
 |
Delete |
Deletes the currently selected vertices, nodes, arcs, or polygons
|
 |
Left |
Activates the cross section to the left of the current cross section as the current cross section
|
 |
Right |
Activates the cross section to the right of the current cross section as the current cross section
|
 |
Print |
Prints the current Graphics Window
|
 |
Auto-Match Cross Section |
Creates a set of straight arcs connecting matching contacts on adjacent boreholes based on the selection to use Horizons or Materials
|
 |
Build Cross Section Polygons |
Deletes all current polygons, builds new polygons using all of the arcs, and checks to see if every polygon built is valid. A polygon is valid only if it contains either one arc representing a borehole region or two arcs representing two matching borehole regions on two holes. Thus, every valid polygon can be assigned one and only one material type. If every polygon built is valid, the Color Fill toggle will be automatically turned on and all polygons built will be filled with the color representing the material they are assigned. Otherwise, a dialog saying "Invalid polygons present" will pop up and all polygons built will be deleted.
|
 |
Delete All |
Deletes all of the vertices, nodes, arcs, and polygons in the current cross section
|
Tool Options
Some tools in the Cross Section Editor contain right-click options. These include:
- Select Point/Node has the following right-click commands:
- Node to Vertices – Converts the selected node to a vertex.
- Select Vertex has the following right-click commands:
- Vertices to Nodes – Converts the selected vertex to a node.
- Select Arc has the following right-click commands:
- Redistribute Vertices – Opens the Redistribute Vertices dialog where the distribution of the vertices on the arc can be adjusted.
- Tin to Arc – Allows selecting a TIN in the project in order to interpolate the TIN elevations to the arc.
- Raster to Arc – Allows selecting a raster in the project in order to interpolate the raster elevations to the arc.
Display Options
| Display Toggle |
Description
|
| Nodes |
Controls the display of the nodes in the graphics window
|
| Vertices |
Controls the display of the vertices in the graphics window
|
| Arcs |
Controls the display of the arcs in the graphics window
|
| Boreholes |
Controls the display of the arcs in the graphics window
|
| Poly fill |
Controls the display of the polygons in the graphics window
|
| Mirror view |
Reverses the order in which the cross sections are displayed
|
| Mark inactive |
Dims the inactive cross sections
|
| Display axes |
Controls the display of the plot axes in the graphics window
|
| Axes behind |
When checked, the axes are drawn behind the cross section. When unchecked, the axes are drawn on top of the cross section.
|
| Material legend |
Controls the display of the material legend
|
