SMS:SRH-2D Files

Output Files

A description of each file generated during an SRH-2D simulation run is as follows. In the file descriptions, * is a placeholder representing the specific case name as specified in the model control:

• *.DAT

  File created when srhpre is run, for use by SRH-2D. It contains model input information as well as geometry information about the mesh.

• *_DIA.dat

  Diagnostic file with potential errors and warnings about the execution. It helps to identify causes of execution error or failure. For the tutorial case, the file is almost empty indicating a successful run of the model.

• *_DIP.dat

  Dynamic Input file allowing users to set up or modify frequently used parameters during an SRH-2D execution. Parameters that can be set up or modified include the total simulation time, number of iterations within each time step, specification of restart files, time interval used for writing out intermediate results, time step interval, damping, relaxation for continuity and momentum equations, and the turbulence model type. See SRH-2D documentation for more information about the implementation of this file.

• *_LNn.dat

  Monitor line file where flow discharge is recorded corresponding to time.

• *_OUT.dat

  Output file providing general model information such as input parameters, mesh size, list of restart file numbers and their corresponding time, cpu time of the simulation, ect.

• *_PTn.dat

  Monitor point file that provides time history of output variables at the user-specified monitor points. The file is in column format and may be imported into Excel for plotting. Output from the file may be used to decide if a steady state solution has been obtained or to examine unsteady change of a variable. If additional monitor points are used, files would have a similar naming convention with the only change being PT2, PT3, etc.

• *_RES.dat

  Residual file that contains residuals of continuity and two velocity equations during the solution. Note that residuals are normalized. For example, the ResH is normalized by the maximum of the first three iterations. Therefore, residual of 1.0 is obtained for ResH if NITER is less than 4 in the c1_DIP.dat file.

• *_RSTn.dat

  Restart file used as a model input in successive runs. These are written out at an interval specified by the user within the model control. If a user has a restart file, they may choose to start a model run using it as the initial conditions of the model.

• *_SOF.dat

  Script Output File generated when SRHpre is run. In the script output file all inputs are saved. Can be used to rerun SRHpre by changing the name to *_SIF.dat

• *_XMDF.h5

  Output file used by SMS for post-processing and visualization of results. Results include water surface elevation, water depth, depth averaged velocity, froude number, and bed shear stress. If a model includes sediment transport, output results could also include critical sediment diameter and sediment transport capacity.

Native Files

SRH-2D makes use of native files. The native files are as follows:

SRHHYDRO File

SRHHYDRO is written out by SMS to guide SRH through the hydraulic simulation. The SRHHYDRO file contains key information about the simulation while acting as a directory to other files for SRH to use. The SRHHYDRO file stores the case name, simulation description, model type, turbulence model information, Manning’s n values, boundary conditions, boundary types, unsteady flow designation, simulation time, resultant output information, and initial conditions. Details of each card in the file are given as follows:

Case	This is an identifier for SRH to use when running to help the user recognize the files that correspond to a specific project. The case should be given a name that is unique for a simulation.
Description	The description is for the user to see in review of what was done for a specific simulation
RunType	This card tells SRH what to compute. Flow means a hydraulic model. Mobile refers to a sediment transport model.
ModelTemp	This card communicates to SRH whether the model will be used to simulate temperature. Currently, temperature is not supported by SRH v. 2.2
UnsteadyOutput	Unsteady output is labeled for unsteady, where intermediate calculations are performed, or as steady, where only final calculations are computed for accuracy.
SimTime	Three numbers are given to specify start time (hours), time step (seconds), and total simulation time (hours).
TurbulenceModel	This option is either parabolic or ke for the current version of SRH.
ParabolicTurbulence	This card is dependent on TurbulenceModel being labeled parabolic. The value is a constant used in the parabolic turbulence equation.
InitCondOption	This card communicates to SRH the condition of each element prior the model run. Options include dry, auto, and rst, where rst represents a start-up file from a previous run.
Grid	This card tells SRH the name of the grid file.
HydroMat	This card tells SRH the name of the material file.
MonitorPtFile	This card tells SRH the name of the monitor point file if one has been created by the user.
OutputFormat	This option represents how SMS will write out the final files to be read back for post processing. Two inputs are required, the file type and the resultant units.
OutputInterval	This card tells SRH how often to write out results during the simulation. The value is given in hours.
ManningsN	In this location two values are given representing the material number and the value of Manning’s n corresponding to that material value. SMS will always write a zero material type as a default.
BC	This card refers to the boundary type. Two values are given representing the boundary number and the type of boundary for each boundary number
IQParams	This card will be written for boundary types that ask for a subcritical inlet boundary. The values given represent the boundary id, the constant flow value or variable flow file name, the units of flow, and the distribution type
ISupCrParams	This card requires the same information as IQParams with the addition of constant water surface elevation or varable water surface elevation file name.
EWSParams	This card represents the stage exit boundary. Values include the boundary id, the constant watersurface elevation or variable watersurface elevation file, and units type.
EQParams	This card gives the constant discharge value or variable discharge file name and unit type.
NDParams	This card refers to a normal depth outlet boundary. Values include the nodestring number at which flow will be computed as well as the average bed slope at the exit location.

The file acts as a map guiding SRH to other important files such as the SRHMAT file, the SRHMONITORPTS file, and the SRHGEOM file.

SRHHYDRO Example

SRHHYDRO 30
Case "Case"
Description "Description"
RunType FLOW
ModelTemp OFF
UnsteadyOutput UNSTEADY
SimTime 0 1 3
TurbulenceModel PARABOLIC
ParabolicTurbulence 0.7
InitCondOption DRY
Grid "HohRiv.srhgeom"
HydroMat "HohRiv.srhmat"
MonitorPtFile "HohRiv.srhmpoint"
OutputFormat XMDF ENGLISH
OutputInterval 1
ManningsN 0 0.02
ManningsN 1 0.025
ManningsN 2 0.07
BC 6 WALL
BC 5 WALL
BC 4 MONITORING
BC 3 MONITORING
BC 2 EXIT-H
BC 1 INLET-Q
IQParams 1 "HohRiv.srhcurve1.xys" EN  CONVEYANCE
EWSParams 2 "HohRiv.srhcurve2.xys" EN

SRHMAT File

The SRHMAT file gives each element a material type. This file will categorize each element to a Manning’s n value.

SRHMAT Example

SRHMAT 30
NMaterials 3
MatName 1 "Channel"
MatName 2 "Forest"
Material 1 1 2 12 14 15 23 24 26 27 28
 29 36 37 38 39 40 41 42 49 50
 51 52 53 54 55 56 63 64 65 66
 67 68 69 70 71 82 83 84 85 86
 87 88 89 90 91 103 104 106 107 108
 109 110 111 112 113 114 115 116 117 118
 119 120 121 132 133 134 135 136 137 138
 139 140 141 142 143 144 145 146 147 148
 149 150 151 152 153 154 155 156 157 158
 159 170 171 172 173 174 175 176 177 178
 179 180 181 182 183 184 185 186 187 188
 189 190 191 192 193 194 195 196 207 208
 209 210 211 212 213 214 215 216 217 218

Material 2 3 4 5 6 7 8 9 10 11 13
 16 17 18 19 20 21 22 25 30 31
 32 33 34 35 43 44 45 46 47 48
 57 58 59 60 61 62 72 73 74 75
 76 77 78 79 80 81 92 93 94 95
 96 97 98 99 100 101 102 105 122 123
 124 125 126 127 128 129 130 131 160 161
 162 163 164 165 166 167 168 169 197 198
 199 200 201 202 203 204 205 206 228 229
 237 238 239 240 241 242 243 244 245 246

SRHMONITORPTS File

The SRHMONITORPTS file or SRHMPOINT file is tells SRH that there are monitor points to watch and where those points are located. SRH will take the coordinates from SMS to locate the areas to be monitored.

SRHMONITORPTS Example

SRHMON 30
NUMMONITORPTS 2
monitorpt 1 798814 309513
monitorpt 2 799387 305853

SRHGEOM File

The SRHGEOM file tells SRH where each element is located and the characteristics of that element. The SRHGEOM file holds information about the units of the grid.

SRHGEOM Example

SRHGEOM 30
Name "HohRiverDomain" 

GridUnit "FOOT"

Elem 1 5 1 6 15
Elem 2 1 2 7 6
Elem 3 3 1 5
Elem 4 2 1 3
Elem 5 5 8 3
Elem 6 3 8 10
Elem 7 9 8 4
Elem 8 13 4 14
Elem 9 14 4 8
Elem 10 11 4 13
Elem 11 4 11 9
Elem 12 14 5 15 24
Elem 13 8 5 14
Elem 14 6 7 17 16
Node 1 798908 309671 169.545
Node 2 798857 309733 170.299
Node 3 798975 309744 171.463
Node 4 799084 309550 170.097
Node 5 798959 309609 169.67
Node 6 798877 309645 169.34
Node 7 798828 309705 170.831
Node 8 799047 309635 171.189
NodeString 6 2 3 10 19 29 40 52 69 90 118
 149 183 217 254 292 330 368 405 441 476
 513 548 585 621 656 687 716 744 771 797
NodeString 5 171 205 240 278 316 354 391 426 462 500
 536 574 610 646 679 710 740 767 793 819
 843 867 891 915 939 963 986 1008 1031 1032

Related Topics

• SRH-2D