GMS:2D Mesh Polygon Attributes: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
(fix formatting)
 
(15 intermediate revisions by one other user not shown)
Line 1: Line 1:
{{2D Mesh links}}
{{2D Mesh links}}
This dialog is used to set the attributes for feature polygons with a [[GMS:SEEP2D|SEEP2D]] or [[GMS:FEMWATER|FEMWATER]] coverage. Attributes that can be specified for each polygon include:
[[File:GMS 2D Mesh Polygon Properties.png|thumb|440 px|The ''2D Mesh Polygon Properties'' dialog]]
This dialog is used to set the attributes for feature polygons with a [[GMS:SEEP2D|SEEP2D]] or [[GMS:FEMWATER|FEMWATER]] coverage. The dialog is reached through the ''Attribute Table'' for a selected polygon in the map coverage. Attributes that can be specified for each polygon include:


==Mesh Type==
==Mesh Type==
Line 13: Line 14:


:[[Image:adapt.png|thumb|left|375 px|Example mesh created using adaptive tessellation]]
:[[Image:adapt.png|thumb|left|375 px|Example mesh created using adaptive tessellation]]
:Adaptive tessellation uses the existing spacing on the polygons to determine the element sizes on the interior. Any interior arcs and refine points are forced into the new mesh. If the input polygon has varying node densities along its perimeter, GMS attempts to create a smooth element size transition between these areas of differing densities. By altering the size bias, the user can indicate whether GMS should favor the creation of large or small elements. Decreasing the bias will result in smaller elements; increasing the bias will result in larger elements. In either case, the elements in the interior of the mesh will honor the arc edges and the element sizes specified at nodes. The bias simply controls the element sizes in the transition region.
:Adaptive tessellation uses the existing spacing on the polygons to determine the element sizes on the interior. Any interior arcs and refine points are forced into the new mesh. If the input polygon has varying node densities along its perimeter, GMS attempts to create a smooth element size transition between these areas of differing densities. By altering the size bias, it is possible to indicate whether GMS should favor the creation of large or small elements. Decreasing the bias will result in smaller elements; increasing the bias will result in larger elements. In either case, the elements in the interior of the mesh will honor the arc edges and the element sizes specified at nodes. The bias simply controls the element sizes in the transition region.


===Patch===
===Patch===
Line 39: Line 40:
:With paving the polygon boundary is "paved" inward until the interior is filled. The mesh triangles created from this method are aligned to the boundary.
:With paving the polygon boundary is "paved" inward until the interior is filled. The mesh triangles created from this method are aligned to the boundary.


:[[Image:paving.gif|center|frame|Example of a mesh created using paving]]
:[[Image:paving.png|thumb|center|375 px|Example of a mesh created using paving]]


==Polygon Type/Material==
==Polygon Type/Material==
Line 47: Line 48:
==Graphical Tools==
==Graphical Tools==


The ''Polygon Attributes'' dialog includes a preview window on the left side. This window shows the arcs and nodes of the selected polygon and allows the user to interact with that definition. The '''Preview''' button generates the elements that will be created for the polygon. It is recommended that the preview is used with the patch and adaptive tessellation options only due to the time required performing density meshing. There are several tools for modifying the existing polygon. Zooming, panning and framing work in the preview window just as they normally would in the graphics window of GMS. They are used to facilitate the selection tools.
The ''Polygon Attributes'' dialog includes a preview window on the left side. This window shows the arcs and nodes of the selected polygon and allows interacting with that definition. The '''Preview''' button generates the elements that will be created for the polygon. It is recommended that the preview is used with the patch and adaptive tessellation options only due to the time required performing density meshing. There are several tools for modifying the existing polygon. Zooming, panning and framing work in the preview window just as they normally would in the graphics window of GMS. They are used to facilitate the selection tools.


All entities are selected by clicking on the entity or by dragging a box to select several entities after selecting the tool. The graphical tools are described in the following table.
All entities are selected by clicking on the entity or by dragging a box to select several entities after selecting the tool. The graphical tools are described in the following table.
Line 54: Line 55:
! Tool !! width ="125" | Tool Name !! Description
! Tool !! width ="125" | Tool Name !! Description
|-
|-
| align = "center" | [[Image:Tool_SelectVertex.png]] || Select Vertex || Select a vertex in the window (red point on arc). Drag the vertex to move it.  
| align = "center" | [[File:GMS Select Vertex Tool.svg|16 px]] || Select Vertex || Select a vertex in the window (red point on arc). Drag the vertex to move it.  
|-
|-
| align = "center" | [[Image:Tool_CreateVertex.png]] || Create Vertex || Create a vertex by clicking on a red arc.
| align = "center" | [[File:GMS Create Vertex.svg|16 px]] || Create Vertex || Create a vertex by clicking on a red arc.
|-
|-
| align = "center" | [[Image:Tool_SelectNode.png]] || Select Point/Node || Select a large blue or red node in the window.
| align = "center" | [[File:GMS Select Node Tool.svg|16 px]] || Select Point/Node || Select a large blue or red node in the window.
|-
|-
| align = "center" | [[Image:Tool_SelectArc.png]] || Select Arc || Selects arcs in the preview window.
| align = "center" | [[File:GMS Select Arc Tool.svg|16 px]] || Select Arc || Selects arcs in the preview window.
|}
|}


Line 67: Line 68:
The options dealing with selected arc(s).
The options dealing with selected arc(s).


*'''Use original n nodes'''. Use the original vertices on the arc (before entering the dialog). If a vertex is moved, deleted, or created using the above tools, clicking this option will not undo the vertex.
*'''Use original n nodes''' – Use the original vertices on the arc (before entering the dialog). If a vertex is moved, deleted, or created using the above tools, clicking this option will not undo the vertex.
 
*'''Distribute n nodes'''. Specify the number of nodes and vertices to put on the arc (minimum of 2). The nodes are evenly spaced if the Bias is 1.0. A Bias of 2.0 will space the nodes more densely to one side; the last space will be twice as big as the first space. A Bias of 0.5 swaps this; the first space is twice as big as the last.  


*'''Distribute n nodes''' – Specify the number of nodes and vertices to put on the arc (minimum of 2). The nodes are evenly spaced if the Bias is 1.0. A Bias of 2.0 will space the nodes more densely to one side; the last space will be twice as big as the first space. A Bias of 0.5 swaps this; the first space is twice as big as the last.


==Node Options==
==Node Options==
[[Image:degen_edge.gif|right|frame|Example of the node options]]
[[Image:degen_edge.png|thumb|right|150 px|Example of the node options]]


The options dealing with selected node(s). These options are used for patches. Patches require 3 or 4 edges. An edge is an arc segment from one blue point to another blue point.
The options dealing with selected node(s). These options are used for patches. Patches require 3 or 4 edges. An edge is an arc segment from one blue point to another blue point.


*'''Split'''. Split two merged arcs. This turns the node blue.
*'''Split''' – Split two merged arcs. This turns the node blue.


*'''Merge'''. Merge two arcs. This turns the node red.  
*'''Merge''' – Merge two arcs. This turns the node red.  


*'''Degenerate Edge'''. This works with 4-sided patches. The degenerate node is treated as an edge, as shown in the figure below.
*'''Degenerate Edge''' – This works with 4-sided patches. The degenerate node is treated as an edge, as shown in the figure below.






{{Navbox GMS}}
{{Navbox GMS}}
[[Category:2D Mesh]]
[[Category:2D Mesh|Pol]]
[[Category:GMS 2D Mesh Dialogs|Pol]]
[[Category:GMS Dialogs|2]]
[[Category:GMS Dialogs|2]]

Latest revision as of 21:16, 28 September 2017

2D Mesh Module
2d mesh.png
2D Mesh
Creating a 2D Mesh
Editing 2D Meshes
2D Mesh Settings
Converting a 2D Mesh to Other Types of Data
More
2D Mesh Display Options
2D Mesh Polygon Attributes
2D Mesh Tool Palette
SEEP2D
Solids to Layered Mesh
2D Mesh Commands
v • e

The 2D Mesh Polygon Properties dialog

This dialog is used to set the attributes for feature polygons with a SEEP2D or FEMWATER coverage. The dialog is reached through the Attribute Table for a selected polygon in the map coverage. Attributes that can be specified for each polygon include:

Mesh Type

Set the meshing type to be used to fill the interior of the polygon. The options include (different options are given according the coverage type):

None

This results in a hole in the finite element network (no elements are created inside the polygon).

Adaptive Tessellation

Adaptive tessellation is a mesh generation technique used to fill the interior of a polygon. A polygon is assigned to be adaptive tessellation in the Polygon Attributes dialog and is filled with the Map → 2D Mesh command.
Example mesh created using adaptive tessellation
Adaptive tessellation uses the existing spacing on the polygons to determine the element sizes on the interior. Any interior arcs and refine points are forced into the new mesh. If the input polygon has varying node densities along its perimeter, GMS attempts to create a smooth element size transition between these areas of differing densities. By altering the size bias, it is possible to indicate whether GMS should favor the creation of large or small elements. Decreasing the bias will result in smaller elements; increasing the bias will result in larger elements. In either case, the elements in the interior of the mesh will honor the arc edges and the element sizes specified at nodes. The bias simply controls the element sizes in the transition region.

Patch

Map Patches

Patching is a mesh generation technique used to fill the interior of a polygon. A polygon is assigned to be a patch in the polygon attributes dialog and is filled with the Feature Objects | Map → 2D Mesh command.
The coordinates of the new nodes on the interior of the patch are computed by constructing a partial bicubic Coons patch using the polygon as patch edges. This ensures that interior nodes are smoothly interpolated from the nodes making up the perimeter of the patch. Patches are applicable when the data points are gathered along parallel lines, such as cross sections in a river.

Rectangular Patches

The following are some hints when using rectangular patches:
The curvature of the patch can change somewhat, but it should not switch directions. If it does, then the patch should be split at the inflection point of the curve.
Although opposite sides in the rectangular patch are not required to have the same number of nodes, the best patches occur when this is close. In the example shown above, the two ends have the same number of nodes and the two sides only differ by three nodes.

Triangular Patches

All three sides of a triangular patch must have the same number of nodes.

Errors

When the patch is previewed in the polygon attributes dialog, the elements in a new patch are checked to make sure they do not overlap each other. If any problems are detected, an error message is given and the patch is not created. Errors may occur especially when the region is highly irregular in shape. In such cases, the region can either be divided into smaller patches, or it can be filled using a different mesh generation technique.
If a polygon cannot be patched, a help string under the preview window in the polygon attributes dialog explains what needs to be changed.

Paving

With paving the polygon boundary is "paved" inward until the interior is filled. The mesh triangles created from this method are aligned to the boundary.
Example of a mesh created using paving

Polygon Type/Material

Polygons can be assigned a Material type.

Graphical Tools

The Polygon Attributes dialog includes a preview window on the left side. This window shows the arcs and nodes of the selected polygon and allows interacting with that definition. The Preview button generates the elements that will be created for the polygon. It is recommended that the preview is used with the patch and adaptive tessellation options only due to the time required performing density meshing. There are several tools for modifying the existing polygon. Zooming, panning and framing work in the preview window just as they normally would in the graphics window of GMS. They are used to facilitate the selection tools.

All entities are selected by clicking on the entity or by dragging a box to select several entities after selecting the tool. The graphical tools are described in the following table.

Tool Tool Name Description
GMS Select Vertex Tool.svg Select Vertex Select a vertex in the window (red point on arc). Drag the vertex to move it.
GMS Create Vertex.svg Create Vertex Create a vertex by clicking on a red arc.
GMS Select Node Tool.svg Select Point/Node Select a large blue or red node in the window.
GMS Select Arc Tool.svg Select Arc Selects arcs in the preview window.

Arc Options

The options dealing with selected arc(s).

  • Use original n nodes – Use the original vertices on the arc (before entering the dialog). If a vertex is moved, deleted, or created using the above tools, clicking this option will not undo the vertex.
  • Distribute n nodes – Specify the number of nodes and vertices to put on the arc (minimum of 2). The nodes are evenly spaced if the Bias is 1.0. A Bias of 2.0 will space the nodes more densely to one side; the last space will be twice as big as the first space. A Bias of 0.5 swaps this; the first space is twice as big as the last.

Node Options

Example of the node options

The options dealing with selected node(s). These options are used for patches. Patches require 3 or 4 edges. An edge is an arc segment from one blue point to another blue point.

  • Split – Split two merged arcs. This turns the node blue.
  • Merge – Merge two arcs. This turns the node red.
  • Degenerate Edge – This works with 4-sided patches. The degenerate node is treated as an edge, as shown in the figure below.


v • e
GMS – Groundwater Modeling System
Modules:2D Grid  •  2D Mesh  •  2D Scatter Point  •  3D Grid  •  3D Mesh  •  3D Scatter Point  •  Boreholes  •  GIS  •  Map  •  Solid  •  TINs  •  UGridsGMS Logo2.png
Models:FEFLOW  •  FEMWATER  •  HydroGeoSphere  •   MODAEM  •  MODFLOW  •  MODPATH  •  mod-PATH3DU  •  MT3DMS  •  MT3D-USGS  •  PEST  •  PHT3D  •  RT3D  •  SEAM3D  •  SEAWAT  •  SEEP2D  •  T-PROGS  •  ZONEBUDGET
Aquaveo
Retrieved from "https://www.xmswiki.com/index.php?title=GMS:2D_Mesh_Polygon_Attributes&oldid=130036"