GMS:2D Mesh Settings: Difference between revisions
From XMS Wiki
Jump to navigationJump to search
Tag: Undo |
|||
| (9 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{2D Mesh links}} | {{2D Mesh links}} | ||
[[File:Preferences2DMesh. | [[File:Preferences2DMesh.png|thumb|left|375 px|The ''Preference'' dialog showing the ''2D Mesh'' tab]] | ||
New nodes in a 2D mesh are created by selecting the '''Create Nodes''' tool from the [[GMS:2D Mesh Tool Palette|''2D Mesh Tool Palette'']] and clicking where the new node is to be located. The default parameters governing the creation of new nodes can be specified using the ''' | New nodes in a 2D mesh are created by selecting the '''Create Nodes''' tool from the [[GMS:2D Mesh Tool Palette|''2D Mesh Tool Palette'']] and clicking where the new node is to be located. The default parameters governing the creation of new nodes can be specified using the '''2D Mesh Settings''' command in the ''Mesh'' menu. This brings up the ''2D Mesh'' tab of the ''Preferences'' dialog. The options in the dialog are as follows: | ||
===Default Z=== | ===Default Z=== | ||
| Line 7: | Line 7: | ||
The options in the center of the dialog are used to specify whether to use a default Z value for all new nodes or to have GMS prompt for the Z value every time a new node is created. | The options in the center of the dialog are used to specify whether to use a default Z value for all new nodes or to have GMS prompt for the Z value every time a new node is created. | ||
===Assign Default Z-Value=== | |||
Select to assign default Z value each time a new node is created. If ''Interpolate for default z on interior'' is selected, the program will interpolate from the already existing values to find the value of new nodes on the interior of the mesh. New nodes on the exterior of the mesh will be assigned the value in the ''Default z'' section. | |||
===Prompt for Z-Value=== | |||
Select for GMS to confirm node value each time a new node is manually created. Each time a new node is manually created, a ''New Node'' dialog will appear with default Z value for the location selected. If the selection is inside the mesh and ''Interpolate for default z on interior'' is selected, the ''New Node'' dialog will populate with the interpolated Z value. If the node is outside the mesh or ''Interpolate for default z on interior'' is not selected, then the ''New Node'' dialog will populate with the value in the ''Default z'' section. | |||
===Insert Nodes into Triangulated Mesh=== | ===Insert Nodes into Triangulated Mesh=== | ||
| Line 14: | Line 20: | ||
If the check box entitled ''Check for coincident nodes'' is selected, any new node created using the '''Create Nodes''' tool will be checked to see if it lies on top of an existing node. | If the check box entitled ''Check for coincident nodes'' is selected, any new node created using the '''Create Nodes''' tool will be checked to see if it lies on top of an existing node. | ||
===Retriangulate Voids when Deleting=== | |||
When selected, GMS retriangulates the elements of a 2D mesh when a node is deleted. When it's off, deleting a node deletes all triangles that connect to that node. | |||
===Thin Triangle Aspect Ratio=== | |||
Sets the minimum aspect ratio for determining thin triangles in the mesh. Triangles with an aspect ratio below the entered value can be selected using the '''Select Thin Triangles''' command or highlighted in the 2D Mesh display options. | |||
===Min Interior Angle for Merging Triangles=== | |||
Defines the minimum interior angle used by GMS to decide which triangles to merge when the [[GMS:Editing 2D Meshes#The_Merge_Triangles_Command|'''Merge Triangles''']] command is used. Each of the angles in the quadrilateral elements created by the '''Merge Triangles''' command will be larger than this defined minimum. Values must be between 0° and 90°. | |||
{{Navbox GMS}} | {{Navbox GMS}} | ||
[[Category:2D Mesh]] | [[Category:2D Mesh|Set]] | ||
[[Category:GMS 2D Mesh Dialogs]] | [[Category:GMS 2D Mesh Dialogs|Set]] | ||
[[Category:GMS Preference Dialogs]] | [[Category:GMS Preference Dialogs]] | ||
[[Category:Preferences]] | [[Category:Preferences]] | ||
