SMS:Release Notes SMS: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
Line 1: Line 1:
Please see the SMS Intermediate Release Bugfixes page for the version of SMS you are interested in:
Please see the SMS Intermediate Release Bugfixes page for the version of SMS you are interested in:
=[[SMS:What's New in SMS 11.1|SMS 11.1 Release]] Bugfixes=
=[[SMS:What's New in SMS 11.1|SMS 11.1 Release]] Bugfixes=
==SMS 11.1.4 - Release April 25, 2013==
This is a version release for SMS 11.1.4
#Resolved an issue allowing the user to only change plot datasets once.
#Fixed an issue causing STWAVE to error out upon running.
#Fixed an issue causing Pre-ADH to fail if material is defined but not in the mesh.
#Fixed an issue causing STWAVE results to be displayed incorrectly.
#Resolved an issue that caused SMS to hang while cleaning a coverage.
#Resolved issues causing the reading in of Curvilinear grids to take much longer than before.
#Resolved an issue causing nodestrings to not have the ability to be merged.
#Fixed an issue causing 'Define Domain' command to not be present in CGWAVE coverage.
#Fixed an issue causing coverages not have the ability to be deleted.
#Resolved an issue causing 'Process Boundary Triangles' to not be visible.
#Resolved an issue causing vectors to pull data from the wrong scalar sets.
#Fixed an issue causing Line Properties to not save or plot correctly.
#Fixed an issue causing a 5th line to not be visible in the Cross Sections Attributes chart.
#Resolved issues related to the CMS-Flow dynamic dialog.
#Fixed an issue causing CMS-Flow solutions to not be read in after model runs.
#Resolved an issue causing the selection of triangles to not work properly if zoomed in too closely.
#Fixed an issue causing a crash to occur after displaying vectors on a grid.


==SMS 11.1.3 - Beta Release April 5, 2013==
==SMS 11.1.3 - Beta Release April 5, 2013==

Revision as of 23:11, 26 April 2013

Please see the SMS Intermediate Release Bugfixes page for the version of SMS you are interested in:

SMS 11.1 Release Bugfixes

SMS 11.1.4 - Release April 25, 2013

This is a version release for SMS 11.1.4

  1. Resolved an issue allowing the user to only change plot datasets once.
  2. Fixed an issue causing STWAVE to error out upon running.
  3. Fixed an issue causing Pre-ADH to fail if material is defined but not in the mesh.
  4. Fixed an issue causing STWAVE results to be displayed incorrectly.
  5. Resolved an issue that caused SMS to hang while cleaning a coverage.
  6. Resolved issues causing the reading in of Curvilinear grids to take much longer than before.
  7. Resolved an issue causing nodestrings to not have the ability to be merged.
  8. Fixed an issue causing 'Define Domain' command to not be present in CGWAVE coverage.
  9. Fixed an issue causing coverages not have the ability to be deleted.
  10. Resolved an issue causing 'Process Boundary Triangles' to not be visible.
  11. Resolved an issue causing vectors to pull data from the wrong scalar sets.
  12. Fixed an issue causing Line Properties to not save or plot correctly.
  13. Fixed an issue causing a 5th line to not be visible in the Cross Sections Attributes chart.
  14. Resolved issues related to the CMS-Flow dynamic dialog.
  15. Fixed an issue causing CMS-Flow solutions to not be read in after model runs.
  16. Resolved an issue causing the selection of triangles to not work properly if zoomed in too closely.
  17. Fixed an issue causing a crash to occur after displaying vectors on a grid.

SMS 11.1.3 - Beta Release April 5, 2013

This is a bugfix release for SMS 11.1.3

  1. Updated the output format of CMS-Flow data.
  2. Resolved an issue that was causing errors after a successful STWAVE run.
  3. Fixed a problem that was causing SMS to write out improper TUFLOW 1D-2D connections.
  4. Resolved an issue where vectors were not showing properly after an STWAVE run.
  5. Modified the manner in which CMS-Wave is executed.
  6. Resolved an issue causing older CMS-Flow project to not read in properly.
  7. Resolved an issue causing CMS-Flow grid data to appear inverted.
  8. Fixed Bouss Sim transects to now display correctly.
  9. Fixed a problem relating to Bouss causing SMS to read in one transect multiple times and others not at all.
  10. Fixed an issue causing projection to get transformed twice.
  11. Resolved an issue causing Map on the fly feature to not work for interpolation of CMS-Flow boundary conditions.
  12. Fixed an issue related to the Bouss Probe Rules window upon creating the coverage.
  13. Resolved an issue causing Edit|Select All feature to not work.
  14. Fixed a problem causing the grid to be hidden after merging grid cells.
  15. Fixed a problem causing project on the fly to not work, which resulted in bad values.
  16. Fixed an issue with Active Materials causing the materials to not show up in sub windows.
  17. Updated various CMS-Flow output features.
  18. Resolved a problem causing data ranges on converted spectra to be inaccurate.
  19. Fixed an issue causing display projection to set to Mercator when shapefile with Geographic projection is already loaded.
  20. Resolved an issue causing Bouss2d projects to not read in properly.
  21. Fixed an issue causing CMS-Flow table count dependencies to not update properly after an insert.
  22. Resolved a problem with processing boundary triangles missing some triangles.
  23. Fixed an issue causing a crash while saving out a CMS-Wave file.
  24. Fixed an issue causing a crash while loading an FLT file as a scatter.
  25. Resolved an issue causing the data set to shop up as a 'z' icon rather than a '123' icon after reading in a survey file as a scatter.
  26. Fixed an issue that required an extra click while selecting a data set for interpolation.
  27. Resolved an issue causing Sediment CML information to not be present while dragging .cmcards onto the SMS shortcut.
  28. Updated CMS-Flow observation points to convert to save points.
  29. Fixed a crash caused while saving out an ADCIRC project.
  30. Resolved an issue causing dynamic images to read in as static images after saving and reloading the project.
  31. Resolved multiple related issues with importing ADCIRC files.
  32. Fixed a problem causing SMS to freeze while writing out certain datasets.
  33. Fixed an issue causing SMS to crash upon deleting Particle Data.
  34. Fixed a crash that was caused from 'Feature Objects|Find' command.
  35. Resolved an issue causing TULFOW downstream BC's to not be saved.
  36. Removed 3D coverage functionality from SMS 11.1 as it is not supported.
  37. Fixed an issue where Dynamic tool bars were not being updated after renaming a coverage and changing its type.
  38. Resolved an issue where SMS would not write 2D-2D TUFLOW grid properly.
  39. Fixed a problem causing splitting of a grid row in CMS Wave to distort all bathymetry values before the split line.
  40. Resolved an issue that caused Observation points to be off by one cell value when read into SMS 11.1.
  41. Adjusted the Location column in the Preferences window to take up the full width of the window.

SMS 11.1.2 - Beta Release February 13, 2013

This is a bugfix release for SMS 11.1.2

  1. Fixed an issue with converting Grids to Maps.
  2. Fixed an issue causing AdH to fail if a material is defined but not in the mesh.
  3. Resolved an issue where loading an RMA2 solution after disabling elements caused the geometry to not match.
  4. Fixed an issue causing the display of scatter sets to not refresh properly.
  5. Fixed an issue causing the FESWMS Model Control BC Descriptor name to not be retained.
  6. Fixed an issue causing an error while reading a wind.in file.
  7. Resolved issues with CMS-FLOW interface and the file formats it writes out.
  8. Fixed an issue with TUFLOW causing the CsDb dialog to not pop up properly.
  9. Resolved a crashing issue with CGWAVE Reset 1D Spacing function.
  10. Resolved an issue with fly reprojection concerning GIS layers.
  11. Resolved an issue with output times not being saved in the AdH Model Control dialog.
  12. Fixed an issue causing CMS Dynamic Datasets to not write out correctly.
  13. Fixed an issue causing SMS to hang while saving a bugged mesh file.
  14. Fixed an issue causing TUFLOW BC Conditions to not be saved.
  15. Fixed an issue where the values in the plot were not matching the values in the dataset.
  16. Fixed an issue where a CMS-FLOW run was trying to read in a file that did not exist.
  17. Resolved an issue where reading in multiple .cmcards files caused the IJ triad to not display in the proper location.
  18. Resolved an issue causing SMS to appear to hang while merging a subset mesh back into a large mesh.

SMS 11.1.1 - Beta Release January 17, 2013

This is a bugfix release for SMS 11.1.1

  1. Fixed an issue with AdH Model losing data.
  2. Fixed issue related to TUFLOW 1D causing a crash.
  3. Fixed issues related to AdH Sediment Bed Layers tab.
  4. Resolved an issue causing processing boundary triangles to miss some triangles.
  5. Fixed a crash caused from reading in a bad .sol file type.
  6. Fixed a crash related to AdH Nodal Boundary conditions.
  7. Fixed a crash caused by saving out BOUSS2D damping information.
  8. Fixed a crash related to merging scatter sets with delete old sets option.
  9. Resolved a tabbing order issue in the AdH model interface.
  10. Resolved an issue with dragging certain coverages into the TUFLOW simulations.
  11. If a user tries to read in an incomplete .sol file type they will now be notified that it is incomplete.
  12. Resolved an issue where SMS was not writing all necessary .hot information out when saving.

SMS 11.1.1 – Beta Release December 11, 2012

This is a bugfix release for SMS 11.1.0

  1. Resolved issues related to interpolating from rasters or raster sets to scatter sets.
  2. Resolved issue related to the display of contours on a raster (or raster set) as a surface. Scalar values were being offset by half a raster cell.
  3. Added a display state for each raster when the raster is saved to an SMS project so that they are not turned on when the project is loaded.
  4. If a user tries to process boundary triangles when the display projection is not the same projection used by the scatter set will immediately tell the user that the display projection must be changed.
  5. The order of rasters in the list will now control the drawing order. Dragging a raster to a lower position in the raster set will hide that raster behind rasters above it in the list.
  6. Messages related to reading incomplete AdH solutions have been modified to reduce the confusion. Redundant messages have been removed. AdH solution folders are now preserved when a project is saved.
  7. Fixed issue with converted selected map (feature) objects to a scatter set.

SMS 11.0 Release Bugfixes

The following bugs have been fixed in this version.

  1. Error in converting a stamped coverage to a scatter set was resolved
  2. When loading a generic mesh in a *.2dm file, with a template that does not correspond to the current model definition, SMS could crash. This problem was resolved to allow for preservation of the grid.
  3. In some situations, when generating a drogue plot or particle trace animation, some of the particles were not getting the new time step data. This has been resolved.
  4. Fixed an error related to interpolation to nodes that are “inactive”. All nodes now get interpolated data regardless of the state of the connected elements.
  5. Calibration plots using the active data set did not update when changing to a completely different scatter set. This has been resolved.
  6. Fixed a drawing order that caused annotation items to appear on top of the film loop clock. The clock now appears on top.
  7. Additional comments were added to the TUFLOW Flow Constriction dialog to make the units and coefficients more understandable.
  8. Bug related to reading in a large RMA2 solution was resolved.
  9. When SMS writes GIS data (or a coverage) as a *.mif/*.mid pair, an extra “bound” record was being written. This has been corrected.
  10. Calibration targets are now not drawn when the observation point falls in an inactive cell/element.
  11. When framing the display, SMS now includes active grid frames.
  12. Fixed erase behind labels to include the film loop clock.
  13. When creating datasets in the dataset toolbox, if all arguments to an operation come from a single folder, the result will now be placed in the same folder.
  14. Fixed a situation where the screen froze trying to display contour labels.

SMS 11.0.11 – Built October 5, 2012

  1. Several internal memory leaks were corrected.
  2. How SMS saves the input wind file for the “Holland Symmetrical” hurricane option for wind in ADCIRC were corrected.
  3. An error related to material sets in TUFLOW was corrected. SMS would lose track of which material set was assigned to a simulation when a project was saved and then read back in.
  4. In some cases it appeared that SMS was deleting data sets from the Project Explorer. In reality, there were just some empty folders that were left in a simulation.
  5. Clarification was made for the “Override Z values” option for TUFLOW in both the dialog and the documention.
  6. In the dataset toolbox, when SMS creates a new data set, the activity was being computed from the resultant nodal activity. This caused single cell/element islands that were inactive to become active. This was changed to use the element activity of the input data sets to compute the resulting element activity.
  7. The ordering of external files in the geometry component file (tgc) is now controlled by the order of the tree items to allow the user to control this explicity.
  8. A crash when loading ADCIRC grid files was resolved. Some files had “Unexpected End of File” messages, and then crashed. They now read in correctly as they did with previous versions.
  9. Error in the TUFLOW interface to “Force cell z to at or below the node z” was resolved. The option is now available without activating the “Set Channel Invert” elevation.
  10. Inconsistent display of rasters corrected.
  11. Error in the SMS steering of CMS-Wave and CMS-Flow was corrected to save the correct eta files.
  12. A file pointer to a shape file was not released when SMS opens the file. This has been corrected.
  13. A issue with user defined palettes was corrected. The first palette was always active when reloading a project. Now SMS looks for a named palette that was active when the project was saved. If that palette exists, it is made current.
  14. SMS has been known to save an illegal material with an ID of zero when saving TUFLOW projects. This should not happen any more.
  15. SMS allows two TUFLOW boundary condition coverages. They cannot be identical or TUFLOW will crash.
  16. Fixed an issue of editing BC curves associated with arcs in a TUFOW coverage. Changing the curve used to change it for other copies. The distinction of multiple curves is now maintained.
  17. Fixed a bug with how WAM grids read in native format are loaded into SMS.
  18. Fixed output of GCL strings for RMA4 to not include the midside nodes.

SMS 11.0.10 – Built September 10, 2012

  1. Additional documentation was added to the help manual on the AdH model control options.
  2. A memory overflow error when triangulating is detected so that SMS does not crash when triangulating very large scatter sets. Several possible solutions to get the data loaded are suggested. A future enhancement will reduce memory requirements for triangulation. This also applies when merging two large scatter sets that cause SMS to try to retriangulate.
  3. Fixed problem when loading STWAVE output files and converting the data sets to scalars. The conversion was creating scalar data sets with “0.0” values.
  4. Fixed an issue with graphics when dragging an arc in the Map Module. During the drag, a phantom arc would appear offset from the arc that was being dragged.
  5. Fixed a problem when forcing breaklines into a TIN that resulted in flat or degenerate triangles. No degenerate triangles should be created now.
  6. A problem with RMA4 giving bad values at midside nodes was isolated and reported to the TABS team at ERDC. No update is expected.
  7. A problem was resolved in the “Holland Symmetrical” hurricane option (NWS = 8).
  8. Resolved an issue with calibration plots when multiple solutions exist.
  9. Fixed spacing in the model wrapper when running AdH to match what is output in a command prompt. This makes the output more readable.
  10. Fixed a crash when creating a telescoping grid for CMS-Flow.
  11. Resolved an issue when reading a TUFLOW solution with overlapping elements at the confluence of two 1D tributaries. SMS deletes the longer (skinnier) triangles that were overlapping, but still reads the data sets for visualization. When these cross sections are properly constructed, there should not be overlapping triangles.
  12. Made change so that when user tries to open the HURDAT database, SMS switches to geographic coordinates to support the data if possible.
  13. Fixed crash related to SMS trying to switch into PBL model even though the interface is not licensed.
  14. Resolved a situation which caused SMS to freeze when dragging a coverage to another location in the project explorer (in Map Module or in a TUFLOW simulation).
  15. Clarified the management of linear –vs- quadratic elements in the mesh module. If both types are permissible, SMS now asks the user to specify the desired type. The default is set to quadratic if quadratic elements exist of when working with TABS or FESWMS. Otherwise, the default is linear.
  16. Fixed a crash when loading multiple map files into SMS.
  17. Added check to verify validity of a coastline file before reading to prevent crash.
  18. Fixed a situation where SMS assigns the wrong material type to polygons created during a conversion from a mesh.
  19. Added support for “TD Card” (the global time step) when converting SMS 10.1 generic model templates to SMS 11.0 format.
  20. Added a warning to let users of the generic model interface be informed that just reading a 10.1 template will not allow use of an 11.0 generic model version.
  21. Fixed conversion of air density for FESWMS when switching from customary units to SI.
  22. Implemented a change to maintain the material set assignments for TUFLOW simulations for an SMS project when saving and reopening the project.
  23. Corrected a linkage problem with scatter data sets being lost when deleting other data sets.
  24. Clarified the documentation and prompts when using the “override Z values” options in the TUFLOW interface. The model supports several options that were causing confusion among users.
  25. Added a right click command in the 1D-2D connections coverage properties to allow users to select the boundary condition coverage to use with 1D-2D connections in the TUFLOW interface.
  26. Fixed a problem with CMS-Flow/CMS-Wave steering that was preventing the “eta” or surge file from being passed to the wave model after a flow simulation.
  27. Fixed a problem with the names of rasters being reset to default value after saving.

SMS 11.0.9 – Built August 6, 2012

  1. Fixed an issue in the CMS-Flow model wrapper to ensure the run time would update.
  2. Fixed a problem with the names of rasters being reset to default value after saving and reloading an SMS project.
  3. Fixed problem with visualization mode to support quadratic elements. This allows switching between visualization mode and TABS without problems.
  4. Fixed error in computing flux across an observation arc. Documented that insufficient resolution, either by saving only TUFLOW corners, or by unrepresented AdH refinement can cause errors in computed flux.
  5. Fixed bug with bad air mass density when converting from customary units to SI and back.
  6. Fixed bug with node labels that stayed visible when nodes were turned off.
  7. Fixed display of node numbers so that they do not overlap nodal elevations when both are turned on.
  8. Fixed a problem with the name that was written to the *.mp file for CMS-Flow when extracting both WSE and velocities along a boundary cellstring.
  9. Fixed a bug when reading in *.2dm file boundary condition on a deleted node string.
  10. Fixed issue with the display of vectors after the mesh is turned off.
  11. Fixed a crash in the AdH materials property dialog when using sediments.
  12. Fixed a tolerance issue when using the Paving function with geographic coordinates and inserting a new mesh into an existing mesh.
  13. Fixed crash when trying to open an STWAVE *.sim file as a CMS Wave *.sim file.
  14. Fixed a bug with the TUFLOW 2D Model Control switching from a Coverage selector to an edit field.
  15. Fixed a crash that occurred sometimes when exporting TUFLOW files.

SMS 11.0.8 – Built July 3, 2012

  1. Fixed an error with exporting STWAVE simulation files.
  2. Fixed a bug that where SMS was crashing when trying to remesh a portion of a mesh when quadratic elements were used.
  3. Fixed an issue where nodestring IDs were not read in correctly.
  4. Fixed a problem where some image files did not display until another item was read in.
  5. Fixed a problem with the generation of damping cellstrings for BOUSS2D.
  6. Corrected an issue first seen in SMS 11.0.4 where internal arcs were not handled correctly when creating a 2D mesh.
  7. Allowed negative values for TUFLOW output start times since TUFLOW allows negative times.
  8. Fixed an issue with ADH iteration controls not reading/writing correctly.
  9. Fixed a crash that sometimes happened when converting GIS data to feature objects.
  10. Fixed a problem where the initial contour display was a solid blue rather than specified values.
  11. Corrected a problem where TUFLOW material sets were put into folders incorrectly.
  12. Fixed an issue where SMS was creating bad triangles when merging scattersets.
  13. Dragging of feature nodes now displays connecting lines while dragging.
  14. Removed an incorrect model check warning when using extracted boundary conditions with CMS-FLOW.
  15. Fixed a crash that sometimes happened when opening two *.tcf files at the same time.
  16. Various bugfixes from software crash reports.

SMS 11.0.7 – Built May 31, 2012

  1. PTM will no longer show not licensed when run from SMS using a single user lock.
  2. Mesh quality not displayed when a mesh is turned off in the project explorer.
  3. Datasets are preserved when saving/loading a project file which wasn’t always working.
  4. When displaying labels on scalar values at mesh nodes, the labels could disappear sometimes. This has been fixed.
  5. Fixed a problem where reading certain *.mif/*.mid files crashed SMS.
  6. Fixed a problem where SMS was hanging when cleaning/merging arcs.
  7. SMS sometimes gave an error message “Unable to write file path for keyword “:NEIGHBOR_FILE” when saving an SMS project.
  8. Fixed a problem where SMS would freeze trying to perform zonal classification.
  9. The CMS-FLOW folder was reorganized to allow 32 and 64 bit executables to both work.
  10. Sometimes SMS was not maintaining the folder structure for loaded XMDF dataset files.
  11. Fixed a problem where zonal classification was not working correctly for Cartesian grids.
  12. TUFLOW events now prevent commas from being used as they don’t work with the TUFLOW file formats.
  13. Fixed an issue where right-clicking on coverage and choosing Map→2D Mesh would operate on the active coverage rather than the one clicked on.
  14. Fixed a problem where the TUFLOW files for geometry components were written out incorrectly when multiple components exist.
  15. Fixed an update problem when using user defined palettes.
  16. Fixed a problem where rotating could cause parts of a functional surface to disappear.
  17. Fixed a problem where the data calculator was not correctly using inactive cells for CMS-FLOW.
  18. Fixed a location where SMS was giving a prompt that the project had changed when it hadn’t.
  19. Changed SMS to not reframe when performing a map→2D mesh.
  20. Fixed a crash when working with user defined tidal constituents in ADCIRC.
  21. Fixed an issue where breaklines of a scatterset were being displayed even though the scatterset was turned off in the project explorer.
  22. Fixed a problem where the runtime wasn’t being updated when running CMS-FLOW.
  23. Turned off a bogus model checker when using CGWAVE when using approximated wave conditions.
  24. Fixed a series of bugs related to setting up a generic model template.
  25. Fixed an issue where SMS was not writing the correct number of frequencies to the STWAVE *.eng file.

SMS 11.0.6 – Built May 4, 2012

  1. Fixed a bug that was introduced in SMS 11.0.5 where SMS would hang when trying to build polygons.
  2. Included a file needed to check for AVI codecs to make sure they would work with SMS. This file is only needed for versions starting with SMS 11.0.5.
  3. Fixed a minor issue where the welcome dialog reported that the SMS was a beta version.
  4. Miscellaneous changes based upon crash logs sent from the software (bugtrap).

SMS 11.0.5 – Built April 25, 2012

  1. Fixed a bug that caused SMS to freeze when using a large duplicate node tolerance.
  2. Corrected the executable used by the BOUSS2D “1D Runup and overtopping calculator.”
  3. Fixed a problem where framing and switching to plan view could change the display of elements and nodes.
  4. Tightened the tolerance used when loading RMA2 files to prevent curves from losing information when loading.
  5. Fixed a problem that sometimes made the generic mesh interface hang.
  6. Fixed a problem where the specified image projection was not written out causing the need to respecify the projection everytime the project was loaded.
  7. Fixed a problem where portion of scatter set not displayed correctly when not filling above/below contour range.
  8. SMS sometimes fouled up a polygon or crashed when moving nodes in the mesh attributes dialog (polygon attribute in mesh coverage).
  9. Corrected an issue where the drogue times in the log file were not reported correctly.
  10. Miscellaneous changes based upon crash logs sent from the software (bugtrap).

SMS 11.0.4 – Built March 3, 2012

  1. Fixed a problem where sometimes a plot didn’t generate correctly for arcs without interior vertices
  2. SMS now closes STWAVE model files after running the model.
  3. Fixed a problem that could occur when closing spectral energy plot and then reopening the plot.
  4. Fixed an issue with the mesh quality min angle not working correctly.
  5. Fixed an issue where the correct tidal constituents was not being displayed when using the Harmonic Analysis option with ADCIRC.
  6. Fixed a problem with default values for nodestrings when using the generic mesh model.
  7. Fixed a problem where the same coverage name in different folders couldn’t be differentiated when using a coverage to display vectors.
  8. Fixed a problem where AdH Iteration control parameters were not being saved.
  9. Fixed a problem with reprojecting a Cartesian grid incorrectly reporting the minimum data value.
  10. Fixed a problem with curve BC data when using the generic mesh model.
  11. Fixed a problem where SMS was freezing when converting scatter breaklines to map.
  12. STWAVE half-plane model only supports spectral energy at 5 degree direction bins. SMS was allowing users to specify a different angle which led to problems when running the model.
  13. SMS was not handling the float/curve option for the generic mesh model correctly.
  14. Fixed a problem where SMS gave a projection error message when loading an image even though the projection was valid.
  15. Fixed a crash when trying to paste data into the cross-section attributes dialog.
  16. Fixed a crash that could sometimes happen when redistributing vertices inside the polygon attributes dialog.
  17. Fixed an issue with losing BC information specified using the generic model interface.
  18. Fixed a problem where the spectral index wasn’t being saved correctly.
  19. Fixed a problem in how STWAVE with breaking datasets when using XMDF dataset output.
  20. Fixed an issue where SMS incorrectly told the user the STWAVE data had changed after saving a file.
  21. Made it so that you can control which raster is the active raster.
  22. Fixed a problem with zoom to raster item.
  23. Made it so SMS would switch modules if you clicked the root raster item.
  24. Add raster module to right-click switch modules in empty area of project explorer.
  25. Fixed a problem where SMS could freeze when trying to build polygons.
  26. Fixed an incorrect model check when working with the CGWAVE model.
  27. Fixed a problem with launching generic mesh models.
  28. Fixed a crash that could occur when specify custom tidal constituents for ADCIRC.
  29. Fixed a crash that could sometimes happen when using functional surfaces and moving windows.
  30. Made it so SMS correctly used the projection associated with a scatterset when reading.
  31. Corrected an issue where datasets created in the dataset calculator could end up in the hotstarts datasets when using AdH.
  32. Fixed a problem where the meshing preview in the polygon attributes dialog for mesh coverages could mess up the polygon’s arcs.
  33. Fixed a crash with PTM and trap files.
  34. Fixed a problem where an error message similar to “No dataset specified for interpolation” when using observation plots with scattersets.
  35. Fixed a crash that could sometimes happen when specifying global parameters for a generic mesh model.
  36. Fixed an error where SMS gave a generic error message when trying to run STWAVE that did not identify the problem.
  37. Fixed a problem where incorrect model setup for WAM could lead to a crash when trying to run the model.
  38. Fixed a problem where contours were not being displayed for elements that were wet but being treated as dry.

SMS 11.0.3 – Built Jan 27, 2012

  1. Fixed a problem where the name of a spectral grid for CMS-Wave was not preserved.
  2. Fixed a problem where grid frames could “disappear” behind other data and not select correctly.
  3. Fixed a crash that could happen when trying to convert a mesh to a map.
  4. Changed SMS to allow small damping cellstrings for the BOUSS2D model.
  5. Fixed a problem with generating cellstrings for BOUSS2D where no cellstring was created on the right side of the grid.
  6. Fixed a problem with the generic model interface where boundary condition values were lost after opening and saving.
  7. Fixed a crash that sometimes could happen when using texture mapping.
  8. Fixed a crash that could happen when using the steering module with CMS-Flow/CMS-Wave.
  9. Made it so you could replace the generic model definition being used without deleting the geometry.
  10. Fixed a problem that caused element labels to print very small at times.
  11. Fixed an issue where SMS would set the ADCIRC output files to binary if the output information wasn’t complete. This made it impossible to get back to ASCII files without editing the files by hand.

SMS 11.0.2

  1. Problem selecting cells in the spectral energy dialog.
  2. Fixed a crash that could happen if you didn’t have a scatter dataset and then converted it to mesh and then to map.
  3. Fixed an issue where mesh elements were not displayed according to the setting in the display options dialog after generating a mesh using LTEA.
  4. Fixed an issue where SMS stored the wrong directory if the user had to path to find the LeProvost files.
  5. Fixed an issue with the LTEA mesh generation feature where SMS was not redistributing the ocean boundary based upon the user specification.
  6. Fixed an issue where LTEA had spurious error messages pop-up during the meshing process.
  7. SMS would sometimes write the wrong timestep when saving datasets to a tabular data file (*.txt).
  8. AdH nodestring symbols were not displayed correctly after loading the simulation until the user went to the boundary condition dialog. This has been fixed.
  9. SMS was not allowing CMS-Wave structure cells to have a negative modification value but this is valid in some cases.
  10. Fixed an issue with the CMS-Wave model control parameters dealing with spreadsheet rows disappearing and not resizing correctly.
  11. Fixed a crash that happened sometimes after duplicating a CMS-Wave grid.
  12. Fixed a problem where the clock for first frame in a filmloop was not being displayed correctly if the starting time was not 0.0.
  13. Fixed a problem where 1D *.mif files were not imported correctly into SMS when loading a *.tcf file.
  14. Fixed a crash with running STWAVE full-plane after loading a project created with an earlier version of SMS.
  15. SMS was not correctly interpreting some of the parameters correctly when importing STWAVE model files.
  16. Fixed a hang when copy/pasting values into the time-series editor used with AdH.
  17. STWAVE executable fixed to write datasets correctly.
  18. Zonal classification could sometimes identify polygons incorrectly.
  19. Auto-zmag was not updating when a new mesh was created until a frame or similar command was issued.
  20. SMS was not correctly remembering specified raster projection after saving/loading a project.
  21. In geographic projections, SMS was labeling x locations “east” that should have been labeled “west.”
  22. The raster contours sometimes changed after going to the display options dialog even when not changing the contour settings.
  23. The 2D Gridframe was sometimes hidden behind raster.
  24. Typo fixed in the menu for data calculator.
  25. STWAVE boundary conditions dialog not “cutting” a row correctly.
  26. Fixed crash when loading a project with 1D elements created in an earlier version of SMS.
  27. Made it so you can specify paths to sediment datasets in *.xmdf file.
  28. Fixed problem displaying functional surfaces with ati card.
  29. Changed how LandXML files read to correctly identify “Northing” then “Easting.”
  30. SMS was incorrectly identifying elements as duplicates and removing them.
  31. Fixed problem with local projection in *.mif/*.mid files.
  32. Fixed crash when snapping two feature points.
  33. STWAVE files not exported correctly when wind datasets being used.
  34. Changed how we handle projections read when importing STWAVE model files so non-state plane coordinates are better handled.
  35. Converting a raster to scatter created voids in the data.
  36. Fixed saving tidal harmonics settings in ADCIRC model control.
  37. You can now select all the points in a raster (before the top values sometimes weren’t selecting).

SMS 11.0.1

  1. Fixed a bug where reprojecting a TUFLOW grid was not updating all of the z values correctly.
  2. Fixed an issue where RMA2 mid-side nodes were not retaining their elevation data after saving/loading.
  3. Fixed a couple minor issues with the Map→scatter dialog.
  4. Made it so SMS would preserve the order of nodestrings from the AdH *.bc file.
  5. Fixed a problem with ADCIRC fort.23 files that were reloading incorrectly.
  6. Fixed a crash that could occur when copy/pasting when making irregular culverts in TUFLOW.
  7. Fixed a problem where the functional surface legend was obscured by other data rather than being above the other data.

SMS 10.1 Intermediate Release Bugfixes

SMS 10.1.11 - Released January 24, 2011

Fixed a problem where doing film loops with cartesian grids with transient datasets used the same time step over and over rather than cycling through the timesteps.

Fixed crash using Map->Scatter.

Fixed an issue where PTM particles would "jump" when going inactive due to improper treatment of NULL values.

Fixed a crash when using ADCIRC<->CMS-WAVE steering module.

Fixed a problem where the volume reported for selected elements is off.

SMS 10.1.10 - Released October 25, 2010

Fixed a problem with converting cartesian grid data to a scatterset.

Fixed a problem where SMS was not saving the georeferencing information for an image.

Fixed zonal classification so it will work correctly with multiple zones and with dynamic solutions correctly.

Fixed a problem where NULL values were not plotted correctly.

Fixed a crash that sometimes occured when going to the page setup dialog.

Fixed a crash that could occur when displaying vectors along nodes in a coverage.

Fixed an issue where the palette used for contour values is not saved and restored with the project.


SMS 10.1.9 - Released September 10, 2010

Fixed an issue with scatter datasets created incorrectly sometimes with data calculator.

Fixed a crash that occurred at times when saving a project after duplicating a scatter set.

Fixed a crash when trying to define a domain using selected vertices.

Fixed an issue with hot starting CMS steering runs.

Fixed a problem where created CGWAVE nodestrings don't get saved with the project.


SMS 10.1.8 - Released July 30, 2010

Fixed a problem where all Bouss2D probes had the results from the first probe.

Fixed a crash interpolating to an ADCIRC grid.

Fixed a problem deleting scatter points.

Fixed a problem where multiple grids could have the same GUID causing one not to get displayed.

Fixed a problem when using Bouss2D and spectra dws files the direction of the wavemaker was not working correctly.

Fixed a problem where SMS would not startup if they moved their "My documents" folder.

SMS 10.1.7 - Released June 17, 2010

Changed the function that copies an STWAVE or CMS-Wave simulation to create a separate copy of the spectra for the new simulation.

Added output files to the data distributed with the RMA2 tutorial

Made a change to where SMS save the log file for TUFLOW to allow non-administrative users to run the model.

Fixed the interactive tool for dragging column boundaries in a CMS grid.

A new update for CMS-Flow resolved a few model crashes that had been reported.

Fixed a bug in mesh generation that occurred when degenerate loops (made out of degenerate arcs) exist in the conceptual model.

Fixed a problem with filtering large dataset using the angle filter.

Fixed a problem related to duplicate node tolerance that occurred when triangulating geographic data.

Fixed the infra gravity wave toolbox for generating input to CGWAVE. This fix also required the distribution of additional utilities in the BOUSS2D folder in the models folder.

Fixed a problem in saving the contour options for a dataset. These were not being preserved from one session to the next with a project.

Fixed a problem interpolating from one scatter set to another.

Fixed a crash that occurred if a user hit the ESC key while saving a scatter set.

Fixed a problem in the color of a grid cell changing.

Fixed a crash in zonal classification.

Fixed a problem when reading ".3dm" files so that the datasets associated with these files are opened automatically.

Fixed a crash that occurred when trying to generate a full circle domain around a single point on a coastline arc.

Fixed the text that appears when you hover over the Select Grid Frame tool.

SMS 10.1.6 - Released May 3, 2010

When saving/loading a FESWMS model the nodestrings do not get duplicated and retain the original direction.

Fixed a problem where some of the FESWMS material properties were not being saved correctly.

Fixed a crash reading some older annotation files.

Potentially Breaking Change - We changed SMS so we no longer provide path information to RMA4 for RMA2 solution files. The issue is that RMA4 does not support very long file names and the binary geometry file has to be in the same folder. We recommend saving/running your RMA4 model in the same directory as you run RMA2. Otherwise, you will need to copy the appropriate files into the same folder as RMA4.

Fixed an issue where a reference to PTM solution files were not being referenced in the project file.

Fixed an issue with appending mesh files that lead to bad values at element centroids.

SMS 10.1.5 - Released March 11, 2010

Fixed the issue with merging meshes that have duplicate or near duplicate nodes deleting border elements and preventing a clean merge.

Fixed a problem where SMS was not saving the PTM setting for "Source and trap z-value relative to datum"

Fixed a problem with the generic model interface that resulted in duplicate global parameter tabs when a 2dm file with the same parameter group was read in.

Fixed an issue that occurred when certain projections were used with Cartesian grids. The problem happened when using the tutorial files with CMS-Flow. The tutorial files have also been changed to the correct projection.

Fixed an issue with display vectors on a grid from CMS-Flow solutions.

Fixed an issue where certain CMS-Flow/CMS-Wave steering files would crash during the steering process if some of the cells along the CMS-Flow boundary condition went dry.

In CMS-Flow the grid is automatically oriented so the origin is in the lower left. This was not working properly and has been fixed.

When adding points to a scatter set, all but the active dataset are deleted. At times the wrong dataset was left. This has been fixed.

SMS 10.1.4 - Released Feb 12, 2010

Fixed a meshing bug that appeared in the last update.

Fixed a problem reading some ADCIRC fort.15 files.

Fixed displaying scatter scalar values colored by contour scheme.

Fixed a BOUSS2D model crash that seemed to happen more with Vista and Windows 7.

SMS now opens project files correctly when you double click on them.

Fixed the data calculator Max(:all) and Min(:all) functions used to determine the max or min of a dataset through all timesteps.

Fixed an issue where the materials boundary lines were not updated correctly when changes were made to the assigned materials.

Fixed an error with the generic model interface reading and writing model parameters.

Fixed some problems with the "Viz" package where features were not accessible like they should be.

Fixed an issue with reading some RMA2 solution files. The files this affected was quite rare.

Fixed a problem with the scatter vertex tolerance in geographic coordinates. This duplicate node tolerance is now always m in geographic coordinates. The conversion isn't precise so it is an approximate value.

Fixed an issue where the label on the initial water surface elevation in a RMA2 simulation was not being updated when the coordinate system of the project changed.

Fixed the graphic and manual for FESWMS wind direction graphics and explanation.

Fixed a problem in the last update where reprojecting cartesian grids removed variable cell widths in CMS-Flow.

SMS 10.1.3 - Released Jan 11, 2010

Fixed a problem where the incident wave condition was not being saved for CGWAVE

SMS defaults ADCIRC fort.73 files to more appropriate names when read in

Fixed a background image shift that was happening in transient animations

Fixed a problem that lead to a bad contour value with CMS-Flow solutions

Reintroduced ability to choose Map to 2D Mesh on an area property coverage to modify the materials in your mesh

Fixed a problem where build polygons was reseting the material types for the polygons

Fixed STWAVE so it ouputs ASCII files when they are selected for output

Fixed a problem reading PTM source files

Fixed a problem where doing a save as project with a PTM simulation referenced the old PTM files

Removed distinguishment of land and water cells in STWAVE and CMS-Wave since no such specification exists in the models. This was causing some cells with solution data to not be displayed.

Fixed an issue with CGWave 1d depth extraction not working.

Fixed a problem where vectors were not saved to a jpeg correctly if the scale was greater than 1.0

Fixed a problem where SMS would sometimes freeze when trying to delete duplicate nodes. This happened particularly when the tolerance was large compared to the average spacing between nodes.

Fixed a problem where CMS-Wave spectra were incorrectly read in as full plane spectra.

SMS now correctly stores the reflection coefficient for CGWAVE

Fixed a problem with displaying cellstrings that had portions with negative z elevations.

SMS 10.1.2 - Released Nov 16, 2009

SMS now reads in fort.61 files correctly.

SMS now creates FESWMS weir IDs correctly.

Fixed a problem where contoured functional surfaces were not displayed correctly.

The feature stamping dialog no longer truncates the words in dialog.

Fixed the roughness by depth image in the FESWMS material property dialogs.

Fixed a problem where you couldn't turn off the legend for contoured functional surfaces.

Readded the capability to do Map->2D Mesh from an area property coverage to copy roughness parameters to an existing mesh.

SMS now correctly updates the screen when triangle edges are swapped without requiring a manual refresh command.

Fixed a problem that profile plots with multiple arcs were not being displayed correctly.

SMS can again show images in the background of flow trace animations.

Fixed a problem with exporting meshes as tabular data files in the 64-bit version.

Fixed a problem where adding scatter points into an existing scatter set caused SMS to hang.

Fixed a problem where converting a scatter contour to an arc broke contour display in other modules.

Fixed some issues with vectors not updating correctly when changing the view.

Fixed an issue where time-series plots of flux were not being computed correctly in the Cartesian Grid Module.

Fixed a problem where splitting a BOUSS2D cellstring caused SMS to hang.

Fixed a problem interpolating vector datasets to a STWAVE grid.

SMS 10.1.1 - Released Oct 26, 2009

Tutorials

New Tutorial – Working with TINs (scattersets) in SMS. Includes guidance on using breaklines and other new features in SMS 10.1

Updated Tutorials – Google Earth tutorial has been updated to show the difference between exporting Raster and Vector KMZ files and to demonstrate how to build KMZ filmloops. The ADCIRC tutorial files have also been updated.

Executables and dlls

The CGWAVE executable for the original installation was incorrect. The correct executable is now being distributed

The correct BOUSS2D executable is now being distributed.

Some of the dll's in the original installation were the incorrect versions. These have been fixed.

Bugs

Windows 7 File Management – There have been some issues with the settings files used by SMS due to inablity to write in the program files area on Windows 7 and/or Vista. These files have been moved to a user area that can be written.

Importing Observation points – Some problems importing observation points have been fixed.

Fixed the “Zoom to “ menu items when right clicking on an object in the project explorer.

Fixed problems related to reproject scattersets.

Fixed a problem with how SMS writes TUFLOW input files when using weirs over structures.

Fixed some problems relating to merging/splitting rows or columns in CMS-Flow.

Fixed functional surface contour legends.

Fixed a problem reading some generic model interface files.

Known Issues

We are currently working to find solutions to the following known issues:

  • SMS 10.1 may not run on virtual machines

SMS 10.0 Intermediate Release Bugfixes

Intermediate release SMS 10.0.11 - February 10, 2009

  • Fixed a merge meshes crash
  • Fixed a problem with RMA2 Marsh Porosity where all of the data was not being saved
  • Fixed a problem with ADCIRC weirs
  • Fixed a problem with zonal classification
  • Fixed a crash in converting GIS shapefiles to feature objects
  • Fixed a problem where RMA2 steering it always reports 0.0% of target

Intermediate release SMS 10.0.10 - December 10, 2008

  • Fixed a crash with converting Shapefiles (GIS) to Feature objects (Map module)
  • Fixed a problem where Shapefile->Map created additional arcs
  • Material Assignments to elements mixed up
  • Fixed a problem with initial values not initializing correctly in the vector to scalar dialog
  • Fixed a crash when opening sms or fpr file
  • Fixed a problem where renaming an arc incorrectly closed a profile plot
  • Fixed a problem where image pyramids were sometimes not setup correctly for large images
  • Fixed a problem where SMS sometimes hung when doing a delete all command
  • Fixed a problem where ADCIRC spatial attributes were not being seeded correctly from the specified dataset
  • Fixed a problem where ADCIRC spatial attributes were not using the default values which caused larger files to be written then were necessary
  • Fixed a problem where reading a partially complete ADCIRC solution was completely aborted rather than reading valid timesteps

Intermediate release SMS 10.0.9 - November 4, 2008

  • Fixed a crash with the material properties for generic model interface
  • Fixed a problem with contour labels showing incorrect values
  • Fixed a problem with the controls to adjust the size of the contour legend
  • Fixed a crash with cleaning really complicated map coverages
  • Fixed a crash with opening project files with plots that have incomplete data
  • Fixed a crash with zonal classification feature
  • Fixed a crash that occurred when moving SMS between monitors when using multiple displays
  • Fixed a crash with the FESWMS global bed control
  • Fixed a problem with demo mode that prevented the user from panning or zooming correctly
  • Fixed a problem with using the virtual earth locator to download teraserver images

Intermediate release SMS 10.0.8 - October 6, 2008

  • Fixed a problem with merging cartesian grid rows and columns
  • Fixed a problem where generating cellstrings along boundary produced overlapping strings

Intermediate release SMS 10.0.7 - August 29, 2008

  • SMS now correctly writes the viscosity data to the appropriate input files
  • Fixed a problem with RMA4 nodestrings with midside nodes
  • Changed find by node ID so that the red circle stays around longer
  • Fixed a crash relating to flux plots
  • Fixed a crash that occured when reading certain project files
  • Fixed a crash relating to boundary conditions with the Generic 2D Mesh Model
  • Fixed a crash that occured when running FESWMS
  • Fixed a problem with an improper wave angle written out when steering with CMS-Wave
  • Fixed a problem with specify input paths for PTM hydrodynamics
  • Fixed a crash when selecting a cell in a grid with no elevation dataset
  • Fixed a problem where the BOUSS2D Wave generator arrow was displayed in the wrong direction
  • Fixed a crash that occured when reading an ADCIRC fort.61 file
  • Fixed a crash that occured when observation coverages were deleted before their associated plots
  • Fixed a problem with converting Cartesian Grid coordinates
  • Fixed so the selection highlighting is done correctly when using the Cartesian Grid Find Cell command.
  • Fixed a crash after deleting materials from the CGWave materials dialog
  • Updated the PTM executable so it will work with hardware locks
  • Fixed a crash when using nested STWAVE grids
  • Fixed a crash that occured when you tried to read in scattered data when the scatter module is not enabled
  • Fixed a crash when reading incomplete FESWMS .sed files
  • Changed SMS to not report PTM warnings for "Mapping Output Interval" if mapping output is turned off
  • You will no longer be prompted to save twice when working with STWAVE
  • SMS now treats ADCIRC fort.73 and fort.74 files correctly in the model control tab
  • Fixed a crash with some RMA4 project files
  • Fixed problems with exporting multiple timesteps into a tabular data file
  • Fixed a problem with functional surfaces not displaying correctly after changing the display options.
  • Fixed an endless loop when trying to create "multiple view" filmloops

Intermediate release SMS 10.0.6 - July 15, 2008

  • A problem with the display getting fouled up after changing the z-mag until the next frame command has been fixed
  • Fixed crash when trying to assign ADCIRC weirs to nodestrings with different numbers of nodes
  • SMS now correctly uses external files specified in the TUFLOW grid options dialog
  • Fixed a problem where invalid material references could be created when using the generic model interface
  • Fixed a crash that happened on certain computers when saving scatter sets as TINs
  • Fixed a problem with the tutorial files for the generic model interface
  • Fixed a crash with multiple view filmloops
  • Inverting cell selection with Cartesian Grids now works correctly
  • Select Cartesian Grid cells by data value has been fixed
  • The node ordering for boundaries and forcing files has been made consistent
  • STWAVE now runs multiple events from SMS
  • The display will now update correctly after changing a nodes x, y coordinates
  • Fixed a crash with observation fluxes
  • Fixed a problem with observation attribute names for arcs when using both nodes and arcs
  • Scatter edges now display correctly when panning after swapping edges
  • The display now updates correctly after reversing the direction of a feature arc
  • Fixed a crash with zonal classification if you enter the dialog with zones defined that don’t have any criteria
  • Fixed Ctrl+ key shortcuts to match the descriptions in the menu
  • When mapping an elevation dataset the correct name is now used
  • Fixed a problem saving TUFLOW event data
  • Select by material type now refreshes appropriately
  • Fixed select by dataset value for nodes
  • Fixed a crash with certain FESWMS sed files
  • Fixed a crash that occurred sometimes when loading a DEM from an asc file
  • Fixed a crash that occurred with Cartesian Grid functional surfaces and ATI graphics cards
  • Modified the Scatter Contour -> Feature dialog to work more cleanly
  • Fixed a crash that occurred with reading some ADCIRC datasets
  • Fixed creating cell strings for PTM from CMS-Flow

Intermediate release SMS 10.0.5 - June 20, 2008

  • Fixed a problem with SMS accessing deleted temporary files.
  • Fixed a crash with trying to access plot data after deleting feature arcs.
  • Bouss-2D wave maker images now appear right side up.
  • Fixed a crash with deleting nodes with nodal boundary conditions being displayed.
  • Fixed a problem with creating PTM input data from an RMA2 solution.
  • Fixed a crash that sometimes occured when smoothing size datasets in the mesh module.
  • Fixed a problem with reading RMA2 mesh and solution files that have gaps in the node ids.
  • Fixed a crash that occured when deleting improperly created Cartesian grid cell strings.
  • Fixed a crash with exporting tabular data.
  • We now give an explanation message if we cannot create a nautical grid.
  • Fixed a problem where sometimes multiple scalar and vector datasets could appear active.
  • SMS now updates the time window when datasets are referenced to a specific timeframe.
  • Fixed a problem where SMS doesn't terminate on exit if a solution dataset has no valid values.
  • Coordinate transforms are now applied to all the grids and not just the active grid.
  • Fixed a meshing crash that sometimes happened with scalar density paving.
  • SMS now writes the TUFLOW initial water level value in the tgc file so it can be overriden by water level polygons.
  • SMS now writes the STWAVE nesting cells correctly.
  • Fixed a problem where it was necessary to launch STWAVE twice before it would run successfully.
  • Fixed a problem with Bouss2D probe dialog.
  • SMS now saves the Cartesian Grid arc options.
  • Changed the output format of the CMS Wave energy file to ensure proper spacing between numbers.
  • The Refine point dialog now uses I and J rather than U and V to be consistent with other parts of the interface.
  • SMS now handles the TUFLOW external grid file correctly.
  • Trying to assign weirs to nodestrings of different numbers of nodes no longer crashes.
  • Fixed a problem with changing the z-magnification that broke the display until the next frame occured.

Intermediate release SMS 10.0.4 - June 11, 2008

  • Mesh contours will now display correctly when there are timesteps that are completely dry
  • Fixed a CMS-Flow, CMS-Wave steering crash
  • Fixed a crash that occured when creating arrowheads using the map draw tools
  • Fixed GIS to Coverage when using a TUFLOW network coverage
  • The profile plot now updates when adding and removing arcs from arc groups
  • Map nodes were drawn in their old location after being dragged to a new location
  • Arcs would sometimes disappear behind transparent contours
  • The origin of observation arcs now save with map files
  • Default stamp elevation for feature stamping is now used correctly
  • Newly created coverages are now active in the project explorer
  • Transparency for Cartesian Grid functional surfaces has been fixed
  • Color filled and linear contours now appear at the same z elevation for Cartesian Grids
  • Naming observation arcs no longer cause a crash
  • Fixed a nodestring display update issue
  • Fixed a crash reading shape files
  • PTM post processing datasets are now saved with the project
  • Triple clicking the same point when creating an arc no longer causes a crash
  • Having multiple CMS Flow grids with cellstrings no longer causes bad cellstrings
  • Trying to save a scatter set to a read only file no longer crashes SMS
  • SMS again allows users to drag files onto the icon to open them
  • An issue with the timestep window not showing up when using PTM has been fixed
  • Fixed a crash when deleting points used by an observation plot
  • There were times when newly created scatter points were not added to the triangulation. This has been fixed.
  • At times SMS would hang when optimizing the triangulation
  • Contour labels are no longer cut off by color filled contours
  • Fixed a selection problem with scatter vertices by when using a polygon
  • Some DEM files were not reading in correctly but they do now
  • TUFLOW 1D Flow vs WSE boundary conditions were not be written to the TUFLOW files correctly
  • The get info dialog for meshes no longer reports information from unused models
  • Fixed the DEM import dialog so that the feedback is correct and makes sense
  • Fixed a problem with display updates when assigning flowrate boundary conditions
  • Functional surfaces now frame correctly
  • The screen refreshes correctly when interpolating between nodes
  • It is now always possible to exit selecting with a box by using the escape key
  • Fixed a crash that occurred when copy a coverage with selected entities
  • Removed excess information from the zonal classification logs
  • Fixed a crash when reading an invalid RMA2 solution
  • SMS now stores Bouss2D grids the right size and with the correct indices
  • Fixed some problems with Bouss2D probes
  • SMS now displays coverages in the correct order
  • Fixed a problem where multiple CGrids sometimes displayed
  • Fixed 1D element contours
  • Fixed problems with grid frames (dragging, deleting, and copying)
  • Fixed a problem with 1D element node updates
  • Coastline files can be created even if you don't have CGWave enabled
  • Fixed a crash with deleting cell strings

Intermediate release SMS 10.0.3 - May 1, 2008

  • PTM executable updated to version 2.025
  • Saving out coastline file available if CGWAVE or ADCIRC is enabled
  • ADCIRC 63/64 file crash
  • Slow deletion of feature points
  • STWAVE coverage issue specifying land polygons
  • GIS to Feature data crash
  • Generic model interface - global parameter definition bug
  • Import wizard problem where z elevations not properly mapped to feature points
  • Fixed multiple views film-loop
  • GIS to Map for TUFLOW network coverage fixed
  • Relocated map node displayed at old location until refresh
  • Origin of observation arc is now saved in the map file
  • Cartesian grid Color fill and linear contours are now displayed at consistent elevations to improve visualizing them in 3D
  • Name observation arc crash
  • Nodestring display issue
  • Fixed create arc tool crash
  • Editing scatter points and overwriting HDF5 file problem
  • Crash when deleting feature points in specific situations

Intermediate release SMS 10.0.2 - March 14, 2008

  • Crash when performing change/delete when triangles selected
  • Print preview not functioning
  • Scale legend does print correctly
  • Text and drawing objects not printing correctly
  • Transform feature objects was not working for PTM coverages
  • STWAVE Boundary conditions types not saved correctly

Intermediate release SMS 10.0.1 - February 19, 2008

  • Fixed the inability to select Southern hemisphere UTM zones
  • Fixed several graphical glitches including texture mapping on a surface and several update problems
  • Fixed various problems with the spectral energy dialog
  • Removed misleading messages that originate from the generic model interface
  • Fixed a crash that sometimes occurred when using zonal classification
  • Fixed a problem with PTM traps that was reporting the open/closed state incorrectly
  • Fixed some issues with models that only support metric units
  • Fixed a crash that sometimes occurred when trying to use LTEA
  • Changed STWAVE to write out all datasets by default
  • Fixed coordinate conversions for PTM sources
  • Fixed a bug that sometimes caused poor meshes to be generated

Related Topics