User:Mburton/13.3 Coverages Tools

13.3 Coverages Tools

This article describes tools from the SMS toolbox designed to perform specialized modifications to to feature objects inside coverages.

Coverages Tools

Features from Raster

The Features from Raster tool derives features such as streams and roadway embankments from an elevation raster.

Input Parameters

• Input raster – Select the input elevation raster.
• Feature type – Select the feature type to generate.
  • "Stream" – This option generates stream lines given the threshold area for stream generation.
  • "Ridge" – This option generates ridge lines for the inverted raster given the threshold area for ridge generation.
• Threshold area – The threshold area to use for stream or ridge generation.
• Pre-processing engine – Which pre-processing engine to use.
  • "rho8" – Computes flow directions and accumulations using the Rho8 algorithm.
  • "Whitebox full workflow" – Computes flow directions and accumulations using the Whitebox tool full workflow algorithm that uses a standard D8 method for computing flow directions.

Output Parameters

• Output coverage – Defines the name of the tool-generated output coverage
• Breached, Flow direction, and Flow accumulation rasters are also generated from this tool. The names of these are currently hardwired to the original raster names ending in _breached, _flowdir, and _flowaccum respectively. An additional extension is added to the end of the raster name based on the pre-processing engine used.

Current Location in toolbox

Coverages/Features from Raster

Polygon from Raster Bounds

The Polygon from Raster Bounds tool creates a new coverage with polygons bounding all of the active regions of the raster. Any inactive regions that fall within an interior polygon will be deleted automatically.

Inactive regions of a raster are determined by the NODATA value of the raster.

Raster containing NODATA cells (shown in red) on the border.

Boundary polygon surrounding the active region of the polygon.

Input Parameters

• Input raster – The raster for which the active boundary polygon will be created.

Output Parameters

• Output coverage – The new coverage to be created, containing the boundary polygon for the active region of the input raster.

Current Location in Toolbox

Coverages/Polygon from Raster Bounds

Polygons from Arcs

The Polygons from Arcs tool converts all arcs in a coverage to polygons based on specified parameters.

This tool is designed to simplify the creation of linear polygons to represent features such as channels or embankments. The feature extraction operations create stream or ridge networks. These features can be used to position cells/elements in a mesh/UGrid to honor these features. However, it is often useful to represent such linear features as Patch polygons to allow or anisotropic cells—elongated in the direction of the feature.

Each arc in the input polygon will be converted to a polygon. The following applies during the creating process:

• The polygon for isolated lines/arcs will consist of offset lines in both directions from the arc. The ends of the polygon will be perpendicular to the end segment of the arc.
• If two arcs are connected (end to end), the orientation of the two polygons will be averaged so that the polygons share and "end".
• If three arcs/lines join at a node, the two that have the most similar direction will be maintained as a continuous feature. The third will be trimmed back to not encroach on the polygons of the other two. If more than three arcs/lines join at a single location, the two arcs with the most similar direction will define the preserved direction. All other arcs will be trimmed back to not encroach.
• If a single arc closes in a loop, the resulting polygon closes on itself. This polygon will not function as a patch in SMS. This workflow is not recommended.
• The tool performs a check to determine if the polygons from two unconnected overlap/intersect each other. This is reported in the progress dialog.

Input Parameters

• Input coverage – This can be any map coverage in the project. The arcs in the coverage will be used to guide polygon creation.
• Average element/cell width – This defines the average width of the segments projecting perpendicular from the arc. The units (foot/meter) correspond to the display projection of SMS.
• Number of elements/cells (must be even) – This defines the number of segments projecting in each direction from the centerline. Because it is projected in both directions, it must be even.
• Bias (0.01-100.0) – This provides control of the relative length of the segments across the feature. In this case, it is actually a double bias because both sides of the feature are biased from the outer edges to the center. Therefore, a bias less than 1.0 results in segments that are shorter at the center. A bias greater than 1.0 results in segments that are longer at the center. Specify a small bias to improve representation of the channel bottom or embankment crest and a larger bias to increase resolution (representation) or the outer edge (shoulder or toes) of the feature. See images below for examples.

Output Parameters

• Output coverage – Specify the name of the coverage to be created that will contain the generated polygons. The intent of this coverage is to be incorporate into a mesh generation coverage for the domain. The resulting coverage will have the Area Property coverage and will need to be changed to the desired coverage type.

Current Location in Toolbox

Coverages/Polygons from Arcs

Examples

Example 1 – 2 segment wide channel

Example 1 Single arc converted to polygon with 2 elements wide

In this case the average element/cell width was set to "w". Since each half has one cell, both segments are "w". The total width is therefore "2.0 w". Since there are only 2 segments, the bias value has no impact in this case.

Example 2 – 4 segment wide channel with bias greater than 1.0

Example 2 Single arc converted to polygon with 4 elements wide with bias of 2.0

In this case with an average segment length (element/cell width) of "w" the total width is "4.0 w". Since the bias is 2.0, the center segments are twice as long as the outer segments.

Example 3 – 4 segment wide channel with bias less than 1.0

Example 3 Single arc converted to polygon with 4 elements wide with bias of 0.5

In this case with an average segment length (element/cell width) of "w" the total width is "4.0 w". Since the bias is 0.5, the center segments are half as long as the outer segments.

Example 4 – 6 segment wide channel with bias greater than 1.0

Example 4 Single arc converted to polygon with 6 elements wide with bias of 2.0

In this case with an average segment length (element/cell width) of "w" the total width is "6.0 w". Since the bias is 2.0, the center segments are twice as long as the outer segments.

Example 5 – End to End Arcs to Polygons

Example 5 Two arcs connected end to end converted to polygons

The offset at the junction of the two arcs is adjusted to be perpendicular to the average of the two arcs. The two polygons would create a continuous channel.

Example 6 – Tributary Arcs to Polygons

Example 6 Two centerlines merging into a single centerline converted to polygons

At the junction of more than two arcs, the two that are closest to linear are assumed to be the main channel and the polygons for those two are treated just like example 5. The other arcs connected to this junction are treated as a tributary. The arc is still converted to a polygon, but any vertices on the arc within two widths of the junction are ignored to allow room for a transition between the channels to occur. (Note: it is anticipated that in the future this will be modified to allow for T or Y type merging of the polygons for junctions of three arcs.)

Example 7 – Parallel Arcs that Result in Overlapping Channel Polygons

Example 7 Two centerlines resulting in overlapping polygons

If two arcs being converted to polygons result in overlapping polygons, the tool reports this issue using one of the overlapping arc indices. It is the responsibility of the modeler to adjust the arcs and convert to non-overlapping polygons, or clean up the overlapping polygons manually.

Error message from Example 7

Related Tools

• Trim Coverage
• Bridge Footprint

Polygon from Raster Nodata

The Polygon from Raster Nodata tool creates a new coverage with polygons bounding all of the active regions of the raster including inactive regions that fall within an interior polygon.

Inactive regions of a raster are determined by the NODATA value of the raster.

Raster containing NODATA cells (shown in purple) shown surrounding a river with dry islands

Polygons surrounding the active region of the raster, including interior islands

Input Parameters

• Input raster – The raster for which the active boundary polygon will be created.
• Number of cells required to make a polygon – The number of cells required to make a polygon. Any interior areas that contain less raster cells than this number will not be enveloped with a polygon.

Output Parameters

• Output coverage – The new coverage to be created, containing the boundary polygon for the active region of the input raster.

Current Location in Toolbox

Coverages/Polygon from Raster Nodata

Template:Polygons from UGrid Boundary Tool

Trim Coverage

The Trim Coverage tool is used to remove features in a coverage that are not desired based on their location. The tool trims all arcs in a selected coverage to the polygons of another selected coverage. Arcs can be trimmed to preserve the portions of the arcs inside or outside of the trimming polygons. The user also specifies a buffer distance to allow the trimming to not retain the intersection points

A specific applications of this tool would be to trim extracted features that are outside of the desired simulation domain. Another application would be to clear out feature arcs that are inside the extents of a predominant feature such as a main river channel.

The tool allows for trimming data to features that are either inside or outside of the desired polygons.

For "large" polygons (> 2500 points), the polygon point locations will be smoothed prior to computing the polygon buffer. This is done because there are cases where the buffer distance combined with the polygon segment orientations causes the buffer operation to be very slow. Smoothing the locations prevents this slowdown.

Input Parameters

• Input coverage containing arcs to be trimmed – Select a coverage from the dropdown list. The arcs on this coverage will be trimmed.
• Input coverage containing polygons to trim by – Select a coverage from the dropdown list. The arcs on this coverage will be used to trim the arcs on the target coverage.
• Trimming option – Trim to inside or Trim to outside.
  • "Trim to inside" – Trim to inside only keeps portions of the arcs that are inside of the polygons. .
  • "Trim to outside" – Trim to outside only keeps the arc portions that are outside of the polygons.
• Trimming buffer distance – Enter a value that defines an offset (either inside if trimming to inside, or outside if trimming to outside) of the trimming polygons. This can be used to keep the results from being too close to the trimming polygon(s).

Output Parameters

• Output coverage – specify the name of the coverage to be created (representing the trimmed arcs).

Current Location in Toolbox

Coverages/Trim Coverage

Related Tools

• Arcs to Polygons