SMS:SRH-2D Coverages

The SRH-2D model makes use of the simulation based modeling approach. This requires defining coverages in the Map module to build the components for use in the SRH-2D simulation.

Boundary Conditions Coverage

Example of the SRH-2D BC Type Parameters dialog showing sediment transport options

The boundary condition coverage consists of a collection of arcs with specified boundary conditions that control the inflow and outflow in a simulation. The coverage itself has the standard coverage item right-click menu commands as well as two specific commands—the HY-8 Options and BC Types commands. These commands are described below.

HY-8 Options

The HY-8 Options command opens the HY-8 Options dialog which allows specifying a link to the location of the HY-8 data file that will be used with this coverage. Only the file name is specified here. If an existing HY-8 file containing culvert crossing attributes already exists, that fie can be selected. Otherwise, a name is specified which will be used when the culvert crossings are defined for this set of boundary conditions. This is an optional parameter and does not need to be filled in unless an HY-8 crossing will be incorporated into the simulation.

BC Types

The BC Types command brings up the BC Types Parameters dialog. This dialog supports the run types "Flow" and "Mobile" described below.

Flow Run Type

The "Flow" option is the default and signifies that the SRH-2D simulation will include only hydrodynamic modeling. If this is the desired type of simulation, this parameter does not need to be changed/set. The following options are available:

• Unsteady Output – Can be set to "On" for unsteady flow or "Off" for steady state flow. (This is not recommended.)

Mobile Run Type

The "Mobile" option is used to perform a sediment transport simulation. It should be noted that sediment transport simulations require a hotstart or restart file from a corresponding hydraulic simulation. When the "Mobile" option is specified the dialog expands to include sediment transport parameters. These are described in SRH-2D Sediment Parameters.

Boundary Conditions

The SRH-2D Linear BC dialog showing a the Inlet-Q option.

SRH-2D support a variety of boundary conditions for hydraulic computation. The boundary conditions for the model are specified through the SRH-2D Boundary Condition coverage by selecting an arc. In SMS 11.2 and earlier versions a boundary could also be defined by selecting a nodestring in the mesh instead, though this is no longer supported in SMS 12.0 and later versions. Once the arc or nodestring has been selected, double-clicking, or right-clicking and using the Assign Linear BC... command, will bring up a dialog where the boundaries can be assigned.

All currently supported boundary types are exterior boundaries that must be placed on the mesh boundary with the exception of a monitor line. Other boundary types include the following: Inlet-Q, Inlet-SC, Exit-EX, Exit-H, Exit-Q, Wall, and Symmetry.

• Inlet-Q is a subcritical inlet boundary that may be given as a constant discharge or as a variable discharge hydrograph. The velocity distribution type may be selected from the boundary condition menu. Inlet flow volume values can only be positive. For a sediment transport run, the inflowing sediment loads are also specified.
• Inlet-SC is a supercritical inlet boundary that may be given as a constant discharge or as a variable discharge hydrograph. Inlet-SC also requires information about depth. Within the boundary condition menu, the velocity distribution type may be specified. Inlet flow volume values can only be positive. For a sediment transport run, the inflowing sediment loads are also specified.
• Exit-EX is a supercritical exit boundary condition.
• Exit-H is a stage type exit boundary where water surface elevation may be given as a constant number or as a stage-discharge or rating curve. Using a constant or rating curve allows accessing the Populate dialog.
• Exit-Q is an exit boundary with a discharge given as a constant number or as a hydrograph.
• Wall
• Symmetry is defined as a boundary where all dependent variables are extrapolated assuming the gradient of the variable in a direction normal to the boundary is zero except the velocity component normal to the boundary.
• Monitor-Line it is an internal polyline which may be used to monitor the total flow discharge and average water surface elevation. For a sediment transport simulation, the total sediment discharge, concentration, average bed elevation, and sediment discharges by size fraction are added to this output.
• Weir – See the SRH-2D Structures article for more information.
• Culvert – See the SRH-2D Structures article for more information.
• Pressure zone – See the SRH-2D Structures article for more information.
• Gate – See the SRH-2D Structures article for more information.

See SRH-2D Boundary Conditions for more information on the options for each boundary type.

Obstructions Coverage

The SRH-2D Obstructions dialog

Used to create feature objects that represent obstructions, such as bank protrusions and boulder clusters. Obstructions can be assigned to feature arcs or points.

When this coverage is active, double-clicking on a feature arc or point, or right-clicking on an arc or point followed by selecting the Assign Obstructions... command, will bring up the Obstructions dialog.

The Obstructions dialog has the following options:

• Obstruction Width/Diameter – Each arc segment represents a rectangular area based on the assigned width. Each point represents a circular diameter based on the assigned width.
• Obstruction Thickness (Z-dir) – Represents the vertical thickness of the obstruction.
• Drag Coefficient (Cd) – A dimensionless coefficient used to describe the surface upon which the water will be flowing around.
• Units – May be assigned to either "ft" (feet) or "m" (meters).
• Porosity – Represents the ability for water to flow through the obstruction object. A porosity of 0 represents a solid surface with no pores allowing for water to pass through the object and 1 represents a surface comparable to a wire mesh with many holes allowing water to pass through it.

Monitor Points Coverage

Monitor Points are optional. If choosing to have monitor points, create a monitor points coverage and add points using the Create Feature Point tool. A monitor point is used to gather specific information for that location at all time steps. Information calculated by SRH-2D at a monitor point includes position in the X and Y direction, bed elevation, water elevation, water depth, X direction velocity component, Y direction velocity component, velocity magnitude, Froude number, and shear stress.

For a sediment transport simulation, the D50 particle size is included in the monitor point output file, and an additional sediment monitor point file is created that includes concentration, erosion and deposition, and bed material gradations.

If a Monitor Points coverage has been created, then it must be linked to the SRH-2D simulation. This can be done by dragging the coverage under the simulation item in the Project Explorer or right-clicking on the coverage and using the Link to menu item. When the simulation is launched, monitoring point data will be collected and outputted.

In SMS 11.2 only, the Monitor Points coverage must be assigned and selected in the Select the Monitor Point Coverage dialog for SRH-2D to recognize them. The dialog is accessed through the Assign Monitor Points Coverage command in the SRH-2D menu. This process is obsolete in SMS 12.0 and higher.

Materials Coverage

The SRH-2D materials coverage allows creating material zones specific to the SRH-2D model. The materials zones must cover the domain extents of the project.

Materials Coverage Right-Click Menu

The materials coverage has the standard coverage item right-click menu commands as well as specific right-click commands. The following commands are also part of the SRH-2D materials coverage:

• Material Properties – Opens the Material Properties dialog.
• Assign Material To – Opens the Assign Materials dialog for managing multiple material coverages.

Assign Materials

Example of the Assign Materials dialog.

SRH-2D allows the option to have multiple material coverages. When multiple material coverages exist, there are options to manage these coverages. By right-clicking on an SRH-2D materials coverage and selecting the Assign Materials to... command, the Assign Materials dialog can be accessed. This dialog allows adding the unique material definition of one material coverage to that of another material coverage. Select the target material coverage that will be modified by the material coverage used to access the dialog. There are then two option for how SMS will modify the target material coverage.

• Append to target material list – This will add any unique material definitions to the target material coverage.
• Replace target material list – Deletes the existing material definitions in the target material coverage and replaces them with the selected material coverage.

After performing either of these actions, opening the Material Properties dialog for the target material coverage will show the material list modified with the new definitions.

Assigning Materials to Polygons

Materials can be assigned to individual polygons using the Select Polygon tool and double-clicking on a polygon in the materials coverage. This will bring up the Assign Material Properties dialog.

The Assign Material Properties dialog can also be reached by right-clicking on a polygon in the materials coverage and selecting the Assign Material Properties command.

See SRH-2D Material Properties for more information about the Assign Material Properties dialog.

Sediment Materials Coverage

The SRH-2D Sediment Materials coverage is similar to the Materials coverage, however, the materials zones in this coverage assign sediment properties. The coverage has the same right-click menu options as the Materials coverage. Sediment materials are assigned to polygons. Sediment layer thicknesses, gradations, and bulk densities (in dry unit weights in lb/ft³ or kg/m³) are provided for each layer. A non-erodible material can be specified by leaving the layer information blank.

For more information, see the Sediment Material Properties article section.

Related Topics

• SRH-2D
• SRH-2D Boundary Conditions
• SRH-2D Material Properties