Template:GMS Define Sources and Sinks Coverage Workflow

1. Create the sources/sinks coverage.

Create a coverage with source/sink attributes. 1. Create new coverage from scratch. Use the New Coverage right-click command. Use the Coverage Setup dialog to create a new coverage by selecting the desired coverage properties and naming the coverage. 2. Create new coverage from an existing coverage. Use the Duplicate command on an existing coverage. This will copy any feature objects on the coverage. Use the Rename command to give the coverage a new name. Change the coverage setup.

2. Create source/sink feature objects.

Create any of the source/sink object needed for the project. Not all source/sink objects are required. 1. Define head arcs or nodes. 1. Create head arcs or points. Create feature arcs or points in the head location. These are often created from existing boundary arcs. 1. Create feature points, arcs, nodes and vertices. In the map module, create feature objects in the active coverage. Use the Create Arc tool to create arcs in the map coverage. Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object. Double-click or press the Enter key to terminate the arc. Use the Create Point tool to create additional nodes alone or to split arcs. 2. Modify arcs. Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation. 1. Create additional vertices on arcs. Use the Create Vertex tool to add vertices along arcs. 2. Refine the arc shape. Use the Select Vertices tool and the Select Points\Nodes tool to move/edit existing arcs and refine the shape by dragging the nodes/vertices. Use the Select Arcs tool to move entire arcs . 3. Split arcs. An existing arc can be split by: 1. Converting a vertex to a node. Use the Select Vertices tool. Select the Feature Objects | Vertices → Nodes command to split the arc into two arcs. 2. Add a node to the arc. Use the Create Point tool to add a node on an arc in order to split it into two arcs. 3. Connect the end of an existing arc to the middle of the arc. Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs. 4. Add a new connecting arc. Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs. 5. Split overlapping arcs using the Clean Options dialog. Select overlapping arcs using the Select Arcs tool. Use the Feature Objects | Clean command to bring up the Clean Options dialog. Select the Intersect selected arcs option (for selected arcs) or Intersect arcs option (for all overlapping arcs) to split the arcs. 4. Merge arcs. Two arcs that share an end node can be merged together. Select the shared node using the Select Points\Nodes tool. Click on the Feature Objects | Nodes → Vertices menu command to merge the arcs. If desired, the Select Vertices tool can be used to select and delete the new vertex. 5. Transform arcs. Select the arc using the Select Arcs tool. Use the Edit | Transform command. Use the Transform dialog to scale, translate or rotate the arc. 2. Add head properties. Using the Select Point/Node tool or Select Arc tool, right-click on the head arc or node and select the Attributes Table command. Define the head properties in the Attribute Table dialog. Heads can be specified or general. 2. Define drain arcs or nodes. 1. Create drain arcs or points. Create feature arcs or points in the drain location. 1. Create feature points, arcs, nodes and vertices. In the map module, create feature objects in the active coverage. Use the Create Arc tool to create arcs in the map coverage. Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object. Double-click or press the Enter key to terminate the arc. Use the Create Point tool to create additional nodes alone or to split arcs. 2. Modify arcs. Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation. 1. Create additional vertices on arcs. Use the Create Vertex tool to add vertices along arcs. 2. Refine the arc shape. Use the Select Vertices tool and the Select Points\Nodes tool to move/edit existing arcs and refine the shape by dragging the nodes/vertices. Use the Select Arcs tool to move entire arcs . 3. Split arcs. An existing arc can be split by: 1. Converting a vertex to a node. Use the Select Vertices tool. Select the Feature Objects | Vertices → Nodes command to split the arc into two arcs. 2. Add a node to the arc. Use the Create Point tool to add a node on an arc in order to split it into two arcs. 3. Connect the end of an existing arc to the middle of the arc. Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs. 4. Add a new connecting arc. Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs. 5. Split overlapping arcs using the Clean Options dialog. Select overlapping arcs using the Select Arcs tool. Use the Feature Objects | Clean command to bring up the Clean Options dialog. Select the Intersect selected arcs option (for selected arcs) or Intersect arcs option (for all overlapping arcs) to split the arcs. 4. Merge arcs. Two arcs that share an end node can be merged together. Select the shared node using the Select Points\Nodes tool. Click on the Feature Objects | Nodes → Vertices menu command to merge the arcs. If desired, the Select Vertices tool can be used to select and delete the new vertex. 5. Transform arcs. Select the arc using the Select Arcs tool. Use the Edit | Transform command. Use the Transform dialog to scale, translate or rotate the arc. 2. Add drain properties. Using the Select Point/Node tool or Select Arc tool, right-click on the drain arc or node and select the Attributes Table command. Define the drain properties in the Attributes Table dialog. 3. Define wells. 1. Create wells points. Create feature points in the well location. 1. Create feature points, arcs, nodes and vertices. In the map module, create feature objects in the active coverage. Use the Create Arc tool to create arcs in the map coverage. Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object. Double-click or press the Enter key to terminate the arc. Use the Create Point tool to create additional nodes alone or to split arcs. 2. Modify arcs. Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation. 1. Create additional vertices on arcs. Use the Create Vertex tool to add vertices along arcs. 2. Refine the arc shape. Use the Select Vertices tool and the Select Points\Nodes tool to move/edit existing arcs and refine the shape by dragging the nodes/vertices. Use the Select Arcs tool to move entire arcs . 3. Split arcs. An existing arc can be split by: 1. Converting a vertex to a node. Use the Select Vertices tool. Select the Feature Objects | Vertices → Nodes command to split the arc into two arcs. 2. Add a node to the arc. Use the Create Point tool to add a node on an arc in order to split it into two arcs. 3. Connect the end of an existing arc to the middle of the arc. Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs. 4. Add a new connecting arc. Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs. 5. Split overlapping arcs using the Clean Options dialog. Select overlapping arcs using the Select Arcs tool. Use the Feature Objects | Clean command to bring up the Clean Options dialog. Select the Intersect selected arcs option (for selected arcs) or Intersect arcs option (for all overlapping arcs) to split the arcs. 4. Merge arcs. Two arcs that share an end node can be merged together. Select the shared node using the Select Points\Nodes tool. Click on the Feature Objects | Nodes → Vertices menu command to merge the arcs. If desired, the Select Vertices tool can be used to select and delete the new vertex. 5. Transform arcs. Select the arc using the Select Arcs tool. Use the Edit | Transform command. Use the Transform dialog to scale, translate or rotate the arc. 2. Add well properties. Using the Select Point/Node tool, right-click on well nodes and select the Attributes Table command. Define the well properties in the Attributes Table dialog. 4. Define stream arcs. 1. Create stream arcs. Create feature arcs in the stream location. 1. Create feature points, arcs, nodes and vertices. In the map module, create feature objects in the active coverage. Use the Create Arc tool to create arcs in the map coverage. Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object. Double-click or press the Enter key to terminate the arc. Use the Create Point tool to create additional nodes alone or to split arcs. 2. Modify arcs. Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation. 1. Create additional vertices on arcs. Use the Create Vertex tool to add vertices along arcs. 2. Refine the arc shape. Use the Select Vertices tool and the Select Points\Nodes tool to move/edit existing arcs and refine the shape by dragging the nodes/vertices. Use the Select Arcs tool to move entire arcs . 3. Split arcs. An existing arc can be split by: 1. Converting a vertex to a node. Use the Select Vertices tool. Select the Feature Objects | Vertices → Nodes command to split the arc into two arcs. 2. Add a node to the arc. Use the Create Point tool to add a node on an arc in order to split it into two arcs. 3. Connect the end of an existing arc to the middle of the arc. Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs. 4. Add a new connecting arc. Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs. 5. Split overlapping arcs using the Clean Options dialog. Select overlapping arcs using the Select Arcs tool. Use the Feature Objects | Clean command to bring up the Clean Options dialog. Select the Intersect selected arcs option (for selected arcs) or Intersect arcs option (for all overlapping arcs) to split the arcs. 4. Merge arcs. Two arcs that share an end node can be merged together. Select the shared node using the Select Points\Nodes tool. Click on the Feature Objects | Nodes → Vertices menu command to merge the arcs. If desired, the Select Vertices tool can be used to select and delete the new vertex. 5. Transform arcs. Select the arc using the Select Arcs tool. Use the Edit | Transform command. Use the Transform dialog to scale, translate or rotate the arc. 2. Add stream properties. Using the Select Arc tool, right-click on the stream arc and select the Attributes Table command. Define the stream properties in the Attributes Table dialog. 5. Define specified flow arcs. 1. Create specified flow arcs. Create feature arcs in the specified flow location. 1. Create feature points, arcs, nodes and vertices. In the map module, create feature objects in the active coverage. Use the Create Arc tool to create arcs in the map coverage. Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object. Double-click or press the Enter key to terminate the arc. Use the Create Point tool to create additional nodes alone or to split arcs. 2. Modify arcs. Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation. 1. Create additional vertices on arcs. Use the Create Vertex tool to add vertices along arcs. 2. Refine the arc shape. Use the Select Vertices tool and the Select Points\Nodes tool to move/edit existing arcs and refine the shape by dragging the nodes/vertices. Use the Select Arcs tool to move entire arcs . 3. Split arcs. An existing arc can be split by: 1. Converting a vertex to a node. Use the Select Vertices tool. Select the Feature Objects | Vertices → Nodes command to split the arc into two arcs. 2. Add a node to the arc. Use the Create Point tool to add a node on an arc in order to split it into two arcs. 3. Connect the end of an existing arc to the middle of the arc. Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs. 4. Add a new connecting arc. Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs. 5. Split overlapping arcs using the Clean Options dialog. Select overlapping arcs using the Select Arcs tool. Use the Feature Objects | Clean command to bring up the Clean Options dialog. Select the Intersect selected arcs option (for selected arcs) or Intersect arcs option (for all overlapping arcs) to split the arcs. 4. Merge arcs. Two arcs that share an end node can be merged together. Select the shared node using the Select Points\Nodes tool. Click on the Feature Objects | Nodes → Vertices menu command to merge the arcs. If desired, the Select Vertices tool can be used to select and delete the new vertex. 5. Transform arcs. Select the arc using the Select Arcs tool. Use the Edit | Transform command. Use the Transform dialog to scale, translate or rotate the arc. 2. Add specified flow properties. Using the Select Arc tool, right-click on the specified flow arc and select the Attributes Table command. Define the specified flow properties in the Attributes Table dialog. 6. Define flow barrier arcs. 1. Create flow barrier arcs. Create feature arcs in the flow barrier location. 1. Create feature points, arcs, nodes and vertices. In the map module, create feature objects in the active coverage. Use the Create Arc tool to create arcs in the map coverage. Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object. Double-click or press the Enter key to terminate the arc. Use the Create Point tool to create additional nodes alone or to split arcs. 2. Modify arcs. Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation. 1. Create additional vertices on arcs. Use the Create Vertex tool to add vertices along arcs. 2. Refine the arc shape. Use the Select Vertices tool and the Select Points\Nodes tool to move/edit existing arcs and refine the shape by dragging the nodes/vertices. Use the Select Arcs tool to move entire arcs . 3. Split arcs. An existing arc can be split by: 1. Converting a vertex to a node. Use the Select Vertices tool. Select the Feature Objects | Vertices → Nodes command to split the arc into two arcs. 2. Add a node to the arc. Use the Create Point tool to add a node on an arc in order to split it into two arcs. 3. Connect the end of an existing arc to the middle of the arc. Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs. 4. Add a new connecting arc. Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs. 5. Split overlapping arcs using the Clean Options dialog. Select overlapping arcs using the Select Arcs tool. Use the Feature Objects | Clean command to bring up the Clean Options dialog. Select the Intersect selected arcs option (for selected arcs) or Intersect arcs option (for all overlapping arcs) to split the arcs. 4. Merge arcs. Two arcs that share an end node can be merged together. Select the shared node using the Select Points\Nodes tool. Click on the Feature Objects | Nodes → Vertices menu command to merge the arcs. If desired, the Select Vertices tool can be used to select and delete the new vertex. 5. Transform arcs. Select the arc using the Select Arcs tool. Use the Edit | Transform command. Use the Transform dialog to scale, translate or rotate the arc. 2. Add flow barrier properties. Using the Select Arc tool, right-click on the flow barrier arc and select the Attributes Table command. Define the barrier properties in the Attributes Table dialog.