|
|
| (12 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| To use [[SMS:SRH-2D|SRH-2D]] monitoring points, follow the steps below: | | To use [[SMS:SRH-2D|SRH-2D]] monitoring points, follow the steps below: |
| {| class="wikitable collapsible collapsed" | | {{SRH Monitor Points Workflow}} |
| |-
| |
| !width="800" style="text-align:left;"|1. SRH-2D project setup.
| |
| |-
| |
| |width="800"|
| |
| {{SRH-2D Project Setup}}
| |
| |}
| |
| | |
| {|class="wikitable collapsible autocollapse" | |
| |-
| |
| !width="800" style="text-align:left;"|2. Create monitor points.
| |
| |-
| |
| |width="800"|
| |
| :The pressure flow boundary conditions must be defined before running the simulation. To do this:
| |
| :#Create a [[SMS:SRH Coverages#Monitor Points Coverage|monitor points]] coverage.
| |
| :#Use the Create Feature Points tool to create monitor points in the coverage.
| |
| |}
| |
| {|class="wikitable collapsible autocollapse"
| |
| |-
| |
| !width="800" style="text-align:left;"|3. Add the monitor points to the simulation.
| |
| |-
| |
| |width="800"|
| |
| :The monitoring points must be added ti the simulation before running SRH-2D. To do this:
| |
| :# Create new [[SMS:Simulations|simulation]].
| |
| :# Add [[SMS:SRH Simulation|components to simulation]].
| |
| :# Add the monitor points coverage to the simulation.
| |
| :# Set up the simulation [[SMS:SRH Model Control|''Model Control'']] parameters.
| |
| |}
| |
| {|class="wikitable collapsible autocollapse"
| |
| |-
| |
| !width="800" style="text-align:left;"|4. Run the SRH-2D simulation.
| |
| |-
| |
| |width="800"|
| |
| :# Save the project.
| |
| :# [[SMS:Model Checker|Check the model]].
| |
| :# [[SMS:SRH Simulation#Running an SRH-2D Simulation|Simulation execution]].
| |
| :# [[SMS:SRH-2D#Troubleshooting|Troubleshooting]].
| |
| |}
| |
| {|class="wikitable collapsible autocollapse"
| |
| |-
| |
| !width="800" style="text-align:left;"|5. Review results.
| |
| |-
| |
| |width="800"|
| |
| Results for the monitoring points can be viewed by doing the following:
| |
| :# Load solution files.
| |
| :# Organize and view solution files in SMS.
| |
| |}
| |
| | |
|
| |
|
|
| |
|
| {{Navbox SMS}} | | {{Navbox SMS}} |
|
| |
|
| [[Category:SMS Workflows]]
| | [[Category:SRH-2D Workflows|Monit]] |
| [[Category:SRH-2D]] | |
Latest revision as of 15:28, 8 March 2016
To use SRH-2D monitoring points, follow the steps below:
| Expand1. Create a Monitor coverage.
|
- Create a new coverage with the SRH-2D "Monitor" type.
- Select Map Data in the Project Explorer and use the New Coverage right-click command.
- Use the New Coverage dialog to create a new coverage by selecting the desired coverage type, and naming the coverage.
|
| Expand2. Create feature points in the coverage.
|
- Use the Create Feature Point
 tool to create points in the coverage. Typically at least two points are created: one in the channel near the upstream boundary, or the bridge opening, and the other in the channel near the downstream boundary.
|
