SMS:Vector Display Options

Vectors display

At a glance

• Visualize vector datasets as arrows
• Constant size or vary by magnitude
• Show just a range of magnitudes
• Color by magnitude

SMS can generate contours from a vector dataset. Vector display is enabled using in the Display Options dialog. Unique vector display options can be set for each module that uses vector datasets.

The options used to generate vectors can be edited by:

• The menu command Data | Vector Options. The data menu is available in most modules. See Module Specific Menus for more information.
• Opening the Display Options dialog.
• The Vector Options Macro. File:Vector Options.bmp

Vector Display Placement and Filter

Display

The Vector Display Placement and Filter section allows the user to control the density of arrow to be displayed. In a very dense mesh, a large number of data points may be displayed very close together on the screen. Therefore, if a vector is displayed at every point, the picture can become a jumble of vectors on top of each other. One way to avoid this is to zoom in on a specific portion of the mesh, so the nodes are not displayed so close together. However, if the desired region of the mesh is still too dense, or zooming in is not acceptable, the user can filter the displayed vectors. SMS provides the following display locations for filtering vectors:

• At each node – Display vectors at each node (data location)
• At corner nodes only – Display vectors at corner nodes only (useful for quadratic elements)
• On a grid – Display vectors on a grid (uniform grid overlaying the mesh or grid geometry). The x and y spacing of the grid are specified in pixels, so regardless of the zoom level the grid remains constant.
• On a coverage – Display vectors on the vertices of feature arcs in the specified coverage (active or specified).

Z-offset

To ensure that the vectors are visible, the Z-offset can be specified to display the vectors a distance above the geometry. The vectors can be filtered further by displaying only a range of magnitudes instead of all vectors.

Arrow Location

Vector arrows can be displayed with the following placement options:

• Tip – Display vectors with the vector arrow tip at the data location.
• Tail – Display vectors with the vector arrow tail at the data location.
• Center – Display vectors with the vector arrow shaft centered over the data location.

Arrow Options

In the Arrow Options section, the user specifies how the arrows will appear in the graphics window. Arrow shaft length can be a constant length, a scaled length, or a range of lengths. The line width of the arrow can also be adjusted. Arrows may be a constant color, or shaded according to magnitude. If a ramp of colors is desired, the color of the vector is extracted from a ramp. By default, the arrow with the smallest magnitude is displayed in the color at the bottom end of the ramp, and the arrow with the largest magnitude is displayed in the color at the top of the ramp. Intermediate magnitudes are interpolated to select an appropriate intermediate color. Alternately, the user can define the magnitudes that map to the top and bottom of the ramp. If this option is used, any arrow with a magnitude lower than the minimum is displayed in the color at the bottom of the ramp, and any arrow with a magnitude greater than the maximum is displayed with the color at the top of the ramp. Users can specify the shape of the arrow head with absolute head length and width values or values proportional arrow length. The style of arrow head is based on the selection of the solid, hollow, and line head types. A preview of the arrows (fixed, or maximum and minimum) based on the selected options are displayed in this section of the dialog.

Legend

The Vector Options also includes a toggle for the display of the vector legend. The vector legend displays the significance of the size of the vectors displayed on the grid. Selecting the legend Options button opens the Vector Legend Options window.

Vector Legend Options

The Vector Legend Options controls the formatting and location of a displayed legend. If a vector dataset exists and is displayed, the legend will be shown if the Legend check box on the Vector Display Options dialog is checked. This window is accessed only from the Legend Options button on the Vector Display Options page of the Display Options dialog.

The Formatting section includes fields for the Title and Units displayed with the legend, a Font selection button for text style, and Height and Width fields for legend size.

Since vector datasets can be displayed for multiple modules at the same time and, therefore, multiple vector legends can be displayed, the Title field can include keywords for convenient labeling. The following title keywords are case sensitive:

• "MODULE" – will be replaced with the title of the vector data set's module
• "DS" – will be replaced with the name of the currently selected vector data set
• "DS:TS" – will be replaced with the name of the currently selected vector data set followed by the current time step

A title of "MODULE DS:TS" is best since it will automatically update as vector data set selection changes.

The Units field includes the single case sensitive keyword of "DEFAULT", which will be replaced with the velocity units of meters per second (m/s) or feet per sceond (ft/s) based on the current coordinate system's horizontal units.

The Location section includes a combo box for specifying the location of the displayed legend. The locations include:

• Top left corner
• Bottom left corner
• Top right corner
• Bottom right corner
• Screen location – specify the location based on screen precentages
• World location – specify the coordinate location

Related Topics

• Contour Options
• Color Ramps
• Display Options
• Visualization