GMS:Horizons Applications: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
Line 42: Line 42:
These images show the solids together and cross section cut through the solids. Again notice how the bottom most material matches across both sets of solids.
These images show the solids together and cross section cut through the solids. Again notice how the bottom most material matches across both sets of solids.


<gallery widths="400 px" heights="300 px">
<gallery widths="400 px" heights="290 px">
Image:AllSolids.png|
Image:AllSolids.png|
Image:AllSolids_XsectXY.png|
Image:AllSolids_XsectXY.png|

Revision as of 15:07, 23 October 2017

Horizons
HorCoverage.png
Links
Horizons
Horizons to Solids
Horizons to 3D Mesh
Horizons to UGrid
Horizons to HUF
Horizons Wizard
Including Borehole Cross Sections
Raster Catalog
Horizons Conceptual Model
Horizons Applications
v • e

The horizons method has been applied at a variety of sites to construct solid models of the subsurface. This page highlights example applications of the Horizons Method.

Modeling a Slope Failure

In this example a combination of boreholes, user-defined cross sections, and TINs were used to create solids at a site with a slope failure.

Borehole data
Surface elevations
Failure surface
User defined cross sections
One user cross section
Zoomed in on cross sections
Solids created from user data
Cross sections from solids
Zoomed in on cross sections

Vertical Boundary Between Solids

In this application, the project required creating a set of solids where there would be distinct materials below a river bed compared to the other materials in the study area. The following cross section shows what a project wanted to create.

Xsect hor application.png


Primary TINs

To create solids that would match this cross section, create two different primary tins and executed the Horizons→Solids command for each primary TIN. The first TIN covered the area of the river and the second TIN covered the remainder of the study area as show in the images below.

Tin1.png Tin2.png

Solids

There are now TINs that defined the top elevations of the horizon surfaces. There were three TINs used in the area around the river and there were four TINs used the remainder of the study area. Solids were created for the river area using the first TIN as the primary TIN. Solids were also created in remainder of the study area by using the second TIN as the primary TIN. Notice the the bottom most material matches in both sets of solids. This is because the same TIN with that horizon was used when creating both sets of solids.

  • Solids river.png
  • Solids StudyArea.png

Cross Sections from Solids

These images show the solids together and cross section cut through the solids. Again notice how the bottom most material matches across both sets of solids.

  • AllSolids.png
  • AllSolids XsectXY.png
  • AllSolids Xsect.png


v • e
GMS – Groundwater Modeling System
Modules:2D Grid  •  2D Mesh  •  2D Scatter Point  •  3D Grid  •  3D Mesh  •  3D Scatter Point  •  Boreholes  •  GIS  •  Map  •  Solid  •  TINs  •  UGridsGMS Logo2.png
Models:FEFLOW  •  FEMWATER  •  HydroGeoSphere  •   MODAEM  •  MODFLOW  •  MODPATH  •  mod-PATH3DU  •  MT3DMS  •  MT3D-USGS  •  PEST  •  PHT3D  •  RT3D  •  SEAM3D  •  SEAWAT  •  SEEP2D  •  T-PROGS  •  ZONEBUDGET
Aquaveo
Retrieved from "https://www.xmswiki.com/index.php?title=GMS:Horizons_Applications&oldid=131195"