WMS:TIN Menu: Difference between revisions

Latest revision as of 19:57, 13 May 2020

The TIN menu in the Terrain Data module has the following commands:

TIN Options: Brings up the TIN Options dialog. See the article TIN Options for more information.

Merge: It is possible to merge a selected TIN with another TIN using the Merge command in the TIN menu. This is particularly useful if wanting to merge a TIN generated from one program with a TIN derived from a background elevation source such as a DEM. For example, a project may have surveyed data with a lot of detail for a part of the project (such as a roadway profile) and it is desired to combine that with a TIN derived from a DEM of the surrounding area.

Before merging

Merged

The following dialog is used to select existing TINs for merging. The merged TINs can be completed merged (all vertices combined and retriangulated), or specified to have vertices in overlapping regions deleted. The old TINs can be kept or deleted.

WMS Merge TINs dialog

The following rules are adhered to when merging a list of TINs:

The TIN at the bottom of the list of TINs to merge has the highest priority, meaning that all of its triangle edges will be preserved while vertices that overlap from TINs higher in the list will be deleted.
If a region being deleted from one TIN overlaps any stream vertices on the TIN being deleted, the stream will be split. The stream will be cut off wherever it "enters" the TIN selected for merging and begin again upstream where it "exits."
Drainage data will be lost and not transferred as part of the merged TIN.

Fill: The Fill command triangulates a selected polygon and merges it with the original TIN. Vertices should be distributed according to the density of TIN vertices desired on the interior of the TIN. The primary purpose is to fill in an area where data is missing on a TIN, or where to retriangulate to a higher density.

It's necessary to have some kind of background elevation behind the polygon (e.g. a DEM or another TIN), or the resulting vertices within the polygon will all have zero elevations.

Filter: Maximum Filter Angle dialog
Redundant and overlapping data may exist in a scattered XYZ datasets. WMS offers the ability to filter the data and remove unnecessary data points in relatively flat areas in the Filter command from the TIN menu. This brings up the Maximum Filter Angle dialog where an angle is specified. Each data point is checked to see if it is in a flat region by dotting the normals of the surrounding triangles.

If the normals are all within the specified angle, the region is considered flat and the point is deleted.

This type of processing is very important when trying to use LIDAR data. Typical LIDAR collection results in resolutions of 1–3 meters so that good detail of flood plains and channel banks is achieved. However, this leaves massive amounts of points in relatively flat areas where the increased resolution is not required (it would be like asking a surveyor to get points every 5 feet just so he doesn't miss anything when hopefully he can be much smarter). The filtering eliminates the points where they are not needed and retains the important points. (The reference to Creighton Omer's paper is about a study using this technique on LIDAR data for hydraulic modeling that concludes a filter angle of 4-8 degrees can be used that will result in up to 85% data reduction without impacting hydraulic modeling results.)

Trim: Trimming allows eliminating all vertices that are outside of a selected feature polygon. First, create the feature polygon in the Map module, then select the polygon to use prior to selecting the Trim command from the TIN menu (Terrain Data module).

Data

The TIN menu offers four options for the using data under the Data submenu:

Calculator

Brings up the Data Calculator. See Datasets for more information.

Smooth Dataset

See Smooth Dataset for more information.

Map Elevation

See the Mapping Elevations section of the Datasets article.

Film Loop

See Setting up Film Loops for more information.

Vertices

See Vertices for more information.. The Tin menu has following options for vertices under the Vertices submenu:

Transform

Used to move TIN vertices according to a specified transformation.

Lock/Unlock

Selected vertices can be locked to prevent them from being dragged or edited.

Delete Duplication

Removes vertices that duplicate the same xy location as another vertex.

Smooth Pits

Adjusts the elevations of pits in order to remove them.

Triangles

See the article Triangulation for more information. The TIN menu gives the following options for triangles under the Triangles submenu:

Triangulate

Triangulates the vertices of the TIN.

Insert Breakline

Optimize Triangulation

Optimizes triangulation according to criteria specified in the TIN Options dialog.

Check Long/Thin Triangles

Remove Flat Triangles

Attempts to eliminate flat triangles on a TIN.

Interpolation

Interpolate TIN To TIN

The Interpolate to TIN command of the TIN menu allows interpolating the elevations of the active TIN to one or more TINs. If more than one other TIN exists, a dialog will appear that allows selecting the TIN(s) to interpolate to. No changes occur in the elevations of the active TIN.

Interpolate TIN To 2D Grid

The Interpolate to 2D Grid command of the TIN menu interpolates the elevations of the active TIN to the 2D grid. Only available if both a TIN and a 2D grid exist.

Interpolate TIN to Feature Objects

This command will interpolate the elevations to feature objects in the active coverage inside the Map module.

Convert

See Convert TINs for more information. The following conversion options are available for TINs:

TIN Contours → Feature

Converts the current linear contours from the TIN to a series of feature arcs which could then be exported as a shapefile.

TIN Boundary → Feature

Creates a boundary feature polygon from the vertices on the boundary of the TIN.

TIN → Scatter Points

Creates a 2D scatter point set from the TIN.

TIN → DEM

Creates a DEM from the TIN.

@@ Line 1: / Line 1: @@
 {{TOCright}}
-The ''TIN'' menu has the following commands:
+The ''TIN'' menu in the Terrain Data module has the following commands:
-==TIN Options==
+; TIN Options : Brings up the ''TIN Options'' dialog. See the article [[WMS:TIN Options|TIN Options]] for more information.
-Brings up the ''TIN Options'' dialog. See the article [[WMS:TIN Options|TIN Options]] for more information.
-==Merging TINs==
+; Merge : It is possible to merge a selected TIN with another TIN using the '''Merge''' command in the ''TIN'' menu. This is particularly useful if wanting to merge a TIN generated from one program with a TIN derived from a background elevation source such as a DEM. For example, a project may have surveyed data with a lot of detail for a part of the project (such as a roadway profile) and it is desired to combine that with a TIN derived from a DEM of the surrounding area.
+<blockquote>
+<gallery mode="packed" heights="300 px" style="text-align:left">
+File:TIN Unmerged.jpg|Before merging
+File:TIN Merged.jpg|Merged
+</gallery>
+</blockquote>
+:The following dialog is used to select existing TINs for merging. The merged TINs can be completed merged (all vertices combined and retriangulated), or specified to have vertices in overlapping regions deleted. The old TINs can be kept or deleted.
-It is possible to merge a selected TIN with another TIN using the '''Merge''' command in the ''TIN'' menu. This is particularly useful if wanting to merge a TIN generated from one program with a TIN derived from a background elevation source such as a DEM.
+::[[Image:WMS Merge TINs.png|thumb|none|left|350 px|WMS ''Merge TINs'' dialog]]
-For example, a project may have surveyed data with a lot of detail for a part of the project (such as a roadway profile) and it is desired to combine that with a TIN derived from a DEM of the surrounding area.
+:The following rules are adhered to when merging a list of TINs:
-{|
+:* The TIN at the bottom of the list of TINs to merge has the highest priority, meaning that all of its triangle edges will be preserved while vertices that overlap from TINs higher in the list will be deleted.
-|-
+:* If a region being deleted from one TIN overlaps any stream vertices on the TIN being deleted, the stream will be split. The stream will be cut off wherever it "enters" the TIN selected for merging and begin again upstream where it "exits."
-|[[File:TIN Unmerged.jpg]] || [[File:TIN Merged.jpg]]
+:* Drainage data will be lost and not transferred as part of the merged TIN.
-|}
-The following dialog is used to select existing TINs for merging. The merged TINs can be completed merged (all vertices combined and retriangulated), or specified to have vertices in overlapping regions deleted. The old TINs can be kept or deleted.
+; Fill : The '''Fill''' command triangulates a selected polygon and merges it with the original TIN. Vertices should be distributed according to the density of TIN vertices desired on the interior of the TIN. The primary purpose is to fill in an area where data is missing on a TIN, or where to retriangulate to a higher density.
-[[Image:WMS Merge TINs.jpg|thumb|none|left|350 px|WMS ''Merge TINs'' dialog]]
+:It's necessary to have some kind of background elevation behind the polygon (e.g. a DEM or another TIN), or the resulting vertices within the polygon will all have zero elevations.
-The following rules are adhered to when merging a list of TINs:
+; Filter : [[Image:WMS Maximum Filter Angle.png|thumb|225 px|''Maximum Filter Angle'' dialog]] Redundant and overlapping data may exist in a scattered XYZ datasets. WMS offers the ability to filter the data and remove unnecessary data points in relatively flat areas in the '''Filter''' command from the ''TIN'' menu. This brings up the ''Maximum Filter Angle'' dialog where an angle is specified. Each data point is checked to see if it is in a flat region by dotting the normals of the surrounding triangles.
-* The TIN at the bottom of the list of TINs to merge has the highest priority, meaning that all of its triangle edges will be preserved while vertices that overlap from TINs higher in the list will be deleted.
+::[[File:TIN FilterAngle.png|335 px]]
-* If a region being deleted from one TIN overlaps any stream vertices on the TIN being deleted, the stream will be split. The stream will be cutoff wherever it "enters" the TIN selected for merging and begin again upstream where it "exits."
+:If the normals are all within the specified angle, the region is considered flat and the point is deleted.
-* Drainage data will be lost and not transferred as part of the merged TIN.
+:This type of processing is very important when trying to use LIDAR data. Typical LIDAR collection results in resolutions of 1&ndash;3 meters so that good detail of flood plains and channel banks is achieved. However, this leaves massive amounts of points in relatively flat areas where the increased resolution is not required (it would be like asking a surveyor to get points every 5 feet just so he doesn't miss anything when hopefully he can be much smarter). The filtering eliminates the points where they are not needed and retains the important points. (The [[WMS:References|reference]] to Creighton Omer's paper is about a study using this technique on LIDAR data for hydraulic modeling that concludes a filter angle of 4-8 degrees can be used that will result in up to 85% data reduction without impacting hydraulic modeling results.)
-==Fill==
+; Trim : Trimming allows eliminating all vertices that are outside of a selected feature polygon. First, create the feature polygon in the Map module, then select the polygon to use prior to selecting the '''Trim''' command from the ''TIN'' menu (Terrain Data module).
-The '''Fill''' command triangulates a selected polygon and merges it with the original TIN. Vertices should be distributed according to the density of TIN vertices desired on the interior of the TIN. The primary purpose is to fill in an area where data is missing on a TIN, or where to retriangulate to a higher density.
-It's necessary to have some kind of background elevation behind the polygon (e.g. a DEM or another TIN), or the resulting vertices within the polygon will all have zero elevations.
+''Data''
+:The ''TIN'' menu offers four options for the using data under the ''Data'' submenu:
+<blockquote>
+; '''Calculator''': Brings up the ''Data Calculator''. See [[WMS:Datasets|Datasets]] for more information.
+; '''Smooth Dataset''' :  See [[WMS:Datasets#Smooth_Dataset|Smooth Dataset]] for more information.
+; '''Map Elevation''' : See the Mapping Elevations section of the [[WMS:Datasets|Datasets]] article.
+; '''Film Loop''' : See [[WMS:Setting up Film Loops|Setting up Film Loops]] for more information.
+</blockquote>
+''Vertices''
+:See [[WMS:Vertices|Vertices]] for more information.. The ''Tin'' menu has following options for vertices under the ''Vertices'' submenu:
+<blockquote>
+; [[WMS:Vertices#Transform_TINs|'''Transform''']] : Used to move TIN vertices according to a specified transformation.
+; [[WMS:Vertices#Locked.2FUnlocked_Vertices|'''Lock/Unlock''']] : Selected vertices can be locked to prevent them from being dragged or edited.
+; [[WMS:Vertices#Delete_Duplicates|'''Delete Duplication''']] : Removes vertices that duplicate the same xy location as another vertex.
+; [[WMS:Vertices#Smoothing_Pits|'''Smooth Pits''']] : Adjusts the elevations of pits in order to remove them.
+</blockquote>
+''Triangles''
+:See the article [[WMS:Triangulation|Triangulation]] for more information. The ''TIN'' menu gives the following options for triangles under the ''Triangles'' submenu:
+<blockquote>
+; '''Triangulate''' : Triangulates the vertices of the TIN.
+; '''Insert Breakline''' :
+; '''Optimize Triangulation''' : Optimizes triangulation according to criteria specified in the [[WMS:TIN Options|''TIN Options'']] dialog.
+; '''Check Long/Thin Triangles''' :
+; '''Remove Flat Triangles''' : Attempts to eliminate flat triangles on a TIN.
+</blockquote>
-==Filter==
+''Interpolation''
-[[Image:WMS Maximum Filter Angle.jpg|thumb|225 px|''Maximum Filter Angle'' dialog]]
+<blockquote>
-Redundant and overlapping data may exist in a scattered XYZ datasets. WMS offers the ability to filter the data and remove unnecessary data points in relatively flat areas in the '''Filter''' command from the ''TIN'' menu. This brings up the ''Maximum Filter Angle'' dialog where an angle is specified. Each data point is checked to see if it is in a flat region by dotting the normals of the surrounding triangles.
-[[File:TIN FilterAngle.png|335 px]]
-If the normals are all within the specified angle, the region is considered flat and the point is deleted.
-This type of processing is very important when trying to use LIDAR data. Typical LIDAR collection results in resolutions of 1&ndash;3 meters so that good detail of flood plains and channel banks is achieved. However this leaves massive amounts of points in relatively flat areas where the increased resolution is not required (it would be like asking a surveyor to get points every 5 feet just so he doesn't miss anything, when hopefully he can be much smarter). The filtering eliminates the points where they are not needed and retains the important points. (The [[WMS:References|reference]] to Creighton Omer's paper is about a study using this technique on LIDAR data for hydraulic modeling that concludes a filter angle of 4-8 degrees can be used that will result in up to 85% data reduction without impacting hydraulic modeling results.)
-==Trimming TINs==
-Trimming allows eliminating all vertices that are outside of a selected feature polygon. First create the feature polygon in the Map module, then select the polygon to use prior to selecting the '''Trim''' command from the ''TIN'' menu (Terrain Data module).
-==Correcting Split Flow==
-Split flow vertices can usually be corrected by finding a channel edge leading into the split flow vertex, and swapping it. This edge swapping can be done automatically using the '''Correct Split Flow''' command from the ''TIN'' menu of the Drainage module. If the edge cannot be swapped without creating overlapping triangles the split flow vertex will not be eliminated and it's necessary to add new vertices, adjust elevations, swap multiple edges or some other form of manual editing technique.
-==Data==
-The ''TIN'' menu offers four options for the using data:
-* '''Calculator''' &ndash; Brings up the ''Data Calculator''. See [[WMS:Datasets|Datasets]] for more information.
-* '''Smooth Dataset''' &ndash;  See [[WMS:Smooth Dataset|Smooth Dataset]] for more information.
-* '''Map Elevation''' &ndash; See the Mapping Elevations section of the [[WMS:Datasets|Datasets]] article.
-* '''Film Loop''' &ndash; See [[WMS:Setting up Film Loops|Setting up Film Loops]] for more information.
-==Vertices==
-The ''Tin'' menu has following options for vertices:
-* [[WMS:Vertices#Transform_TINs|'''Transform''']] &ndash; Used to move TIN vertices according to a specified transformation.
-* [[WMS:Vertices#Locked.2FUnlocked_Vertices|'''Lock/Unlock''']] &ndash; Selected vertices can be locked to prevent them from being dragged or edited.
-* [[WMS:Vertices#Delete_Duplicates|'''Delete Duplication''']] &ndash; Removes vertices that duplicate the same xy location as another vertex.
-* [[WMS:Vertices#Smoothing_Pits|'''Smooth Pits''']] &ndash; Adjusts the elevations of pits in order to remove them.
-See [[WMS:Vertices|Vertices]] for more information.
-==Triangles==
-The ''TIN'' menu gives the following options for triangles:
-* '''Triangulate'''
-* '''Insert Breakline'''
-* '''Optimize Triangulation'''
-* '''Check Long/Thin Triangles'''
-* '''Remove Flat Triangles'''
-See the article [[WMS:Triangulation|Triangulation]] for more information.
-==TIN Interpolation==
 ;Interpolate TIN To TIN : The '''Interpolate to TIN''' command of the ''TIN'' menu allows interpolating the elevations of the active TIN to one or more TINs. If more than one other TIN exists, a dialog will appear that allows selecting the TIN(s) to interpolate to. No changes occur in the elevations of the active TIN.
 ; Interpolate TIN To 2D Grid : The '''Interpolate to 2D Grid''' command of the ''TIN'' menu interpolates the elevations of the active TIN to the 2D grid. Only available if both a TIN and a 2D grid exist.
 ; Interpolate TIN to Feature Objects : This command will interpolate the elevations to feature objects in the active coverage inside the Map module.
+</blockquote>
-==Convert==
+''Convert''
-The following conversion options are available for TINs:
+:See [[WMS:Convert TINs|Convert TINs]] for more information. The following conversion options are available for TINs:
-* '''TIN Contours &rarr; Feature'''
+<blockquote>
-* '''TIN Boundary &rarr; Feature'''
+; '''TIN Contours &rarr; Feature''' : Converts the current linear contours from the TIN to a series of feature arcs which could then be exported as a shapefile.
-* '''TIN &rarr; Scatter Points'''
+; '''TIN Boundary &rarr; Feature''' : Creates a boundary feature polygon from the vertices on the boundary of the TIN.
-* '''TIN &rarr; DEM'''
+; '''TIN &rarr; Scatter Points''' :Creates a 2D scatter point set from the TIN.
+; '''TIN &rarr; DEM''' : Creates a DEM from the TIN.
-See [[WMS:Convert TINs|Convert TINs]] for more information.
+</blockquote>
 ==Related Topics==
@@ Line 92: / Line 82: @@
 * [[WMS:2D Grid Module|2D Grids]]
 * [[WMS:Interpolation Options|Interpolation Options]]
+* [[WMS:Drainage_Module_Menus#Drainage_TIN_Menu|Drainage TIN Menu]]
@@ Line 98: / Line 89: @@
 [[Category:TINs|M]]
 [[Category:TIN Dialogs|Men]]
+[[Category:Gallery]]

v • e WMS – Watershed Modeling System
Modules:	Terrain Data • Drainage • Map • Hydrologic Modeling • River • GIS • 2D Grid • 2D Scatter
Models:	CE-QUAL-W2 • GSSHA • HEC-1 • HEC-HMS • HEC-RAS • HSPF • MODRAT • NSS • OC Hydrograph • OC Rational • Rational • River Tools • Storm Drain • SMPDBK • SWMM • TR-20 • TR-55
Toolbars:	Modules • Macros • Units • Digitize • Static Tools • Dynamic Tools • Drawing • Get Data Tools
Aquaveo

WMS:TIN Menu: Difference between revisions

Latest revision as of 19:57, 13 May 2020

Contents

Related Topics

Navigation menu

Page actions

Page actions

Personal tools

XMS Projects

Search

Links

Tools