WMS:Drainage Module Menus

The TIN and DEM menus have different commands when the Drainage module is active.

Drainage TIN Menu

The TIN menu for the Drainage module contains the following commands:

Node↔Outlet

A selected node or vertex can be converted to an outlet node in a drainage coverage using the Node↔Outlet command in the DEM menu (an existing outlet can be converted back to a node as well). If a vertex is converted to an outlet the vertex is first converted to a node and the attribute of the node is then set to be drainage outlet rather than generic. This is equivalent to setting the attribute of the node within the Map module in the normal fashion, but is added to the DEM menu for ease and for completeness of the process.

Create Stream

Create Pipe

Display Stream Profile

Delete Stream Segements

Define Basins

Refine Boundaries

Merge Basins

Drainage DEM Menu

The DEM menu for the Drainage module contains the following commands:

Compute Flow Direction/Accumilation

Import Flow Direction/Accumilations

Flow directions and accumulations are typically determined using a program, such as ArcView®, GRASS, or TOPAZ. Resulting grid files can then be imported into WMS. See Importing Flow Directions and Accumulations for more information.

Node↔Outlet

A selected node or vertex can be converted to an outlet node in a drainage coverage using the Node↔Outlet command in the DEM menu (an existing outlet can be converted back to a node as well). If a vertex is converted to an outlet the vertex is first converted to a node and the attribute of the node is then set to be drainage outlet rather than generic. This is equivalent to setting the attribute of the node within the Map module in the normal fashion, but is added to the DEM menu for ease and for completeness of the process.

Arcs→Outlets

The Arcs→Outlets command in the DEM menu of the Drainage module will automatically place a new outlet feature point at all intersections of a selected arc (required input to the command) and the specified flow accumulation value. The default flow accumulation threshold will correspond to the current display options setting and represents the area upstream. This is particularly useful if wanting to establish outlets for a series of drainages that a highway or other important line feature will cross as illustrated in the figure below.

Outlets created with the Arcs⇒Outlets command

The arc should exist in a drainage coverage or the nodes created by the intersection will be generic nodes rather than drainage outlets.

DEM→Steam Arcs

used to create feature arcs from DEM points whose flow accumulation areas are above a defined threshold. An arc vertex is created for each DEM point that has a flow accumulation value greater than the threshold entered. Consecutive stream DEM points are then joined together as arcs with nodes created at junction points where the stream splits.

Outlet points should be created where the watershed outlet of the study area is. These outlet points could be at any DEM point, but should be in a DEM point that has a high enough flow accumulation to pass the threshold (WMS will snap outlet points to the closest threshold cell when creating them in the Drainage module). The Flow Accumulations display option can be very useful for identifying these points and for determining what an appropriate threshold area is.

Define Basins

When the command is used the DEM points intersected by the stream arcs are assigned the basin ID already given to the arcs. The Define Basins procedure then continues by tracing the flow paths of the remaining DEM points until a point which has already been assigned a basin ID is intersected. The result is that each DEM point gets assigned the ID of the sub-basin it belongs to. See DEM Basins for more information.

Basins→Polygons

Once the desired sub-basin delineation from the DEM points has been defined, the basin boundaries can be converted to feature polygons. This is done by tracing the boundaries between sub-basins to generate arcs. After all of the boundaries have been defined the arcs are converted to polygons and the polygons assigned the appropriate basin ID.

The resulting polygon boundaries will be jagged because the arcs created for the polygons trace around each raster DEM cell. In order to make the boundaries appear smoother and more visually appealing, redistribute vertices along a cubic spline. If using a 30 meter resolution DEM then the average length between vertices will be approximately 30 meters and it is suggested to redistribute to about 100 meters spacing (be sure to turn on the cubic spline option). In general, redistributing to about three times the DEM resolution will produce good results.

Merge Selected Basins

Merges two selected sub basins into a single basin. The two sub basins must be directly connected to the same outlet point.

By default WMS will create a separate basin for each upstream branch of an outlet point. However, some may wish to combine basins of all branches of an outlet into a single basin. The Merge Selected Basins command allows doing this.

An alternative approach (and really a better way to do it for data management purposes) is to define the basin just downstream of the junction as illustrated in the following figure.

Define basin just downstream of junction

Delete NULL Basins Cell Data

Used to delete all DEM points which are not currently assigned a basin ID. The DEM is reduced to a bounding rectangle of the watershed and elevation values within the rectangle but outside of the watershed are converted to NODATA.

Compute Basin Data

Compute Gage Weights

Delineate Basins Wizard

The DEM Guidelines article outlines as steps the basic process for watershed characterization with DEMs. Some of these steps are repeated quite frequently. Rather than needing to perform them one at a time, select the Delineate Basins Wizard command and the steps will be performed in succession.

In order to run the Delineate Basin Wizard, the project should have already read in elevations (edited if desired), run TOPAZ to compute the flow directions and flow accumulations, and established initial outlet points. The wizard will then convert the outlets to streams, define basins, convert the basins to polygons, and compute basin data in succession.

The delineation wizard is best suited for use when there is a single basin to delineate rather than several smaller basins that make up a larger basin. For such cases it is probably best to follow the individual steps to prevent lumping the multiple smaller sub-basins into a single large basin.

Draw Flow Patterns

Initiates a flow path from the DEM points according to the current display step. By drawing flow paths from the DEM points a visual queue of the watershed flow patterns can be obtained. If a basin polygon is selected prior to issuing the command then flow paths will only be drawn for the DEM points that are part of the selected basin. The display step of the flow patterns can be controlled by modifying the Point Display step option in the DEM Display Options dialog.

Individual flow paths may also be drawn using the Draw Flow Path tool.

Compute Area Between Elevations

Polygon Basin IDs→DEM

Assigns basin IDs to the DEM from a set of polygons that represent basin boundaries. This command is useful if not delineated the basin using the flow directions and flow accumulations from within WMS, but instead using a set of polygons representing basin boundaries with unique IDs. Once basin IDs have been assigned, basin data such as area, average slope, etc. can be computed.

Only use this option if there is a set of feature objects already and/or wishing to “over-ride” the basin boundaries that are determined from elevation data. This might occur in an urban watershed where streets, canals, etc. may not be apparent in the digital elevation data.

Export TOPAZ File

The Export TOPAZ File command is provided for those who wish to use TOPAZ for purposes outside of what WMS needs (the flow direction and accumulation files). This format should be close to the public domain version of TOPAZ, but may be slightly out of date.

Related Topics

• Drainage Coverage
• Watershed Delineation with DEMs