WMS:SMPDBK Post Processing: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
No edit summary
No edit summary
 
(18 intermediate revisions by the same user not shown)
Line 1: Line 1:
To view results of an SMPDBK analysis, you should perform the following steps:
To view results of an SMPDBK analysis, perform the following steps:


1. Run the simulation by selecting '''Run Simulation''' in the ''SMPDBK'' menu.
#Run the simulation by selecting '''Run Simulation''' in the ''SMPDBK'' menu.
 
#Using the Map Module, interpolate the water surface elevations in the 1D Hyd Centerline and 1D Hyd Cross Section coverages. This can be done by selecting each coverage to make it active and then selecting '''Interpolate Water Surface Elevations''' from the ''River Tools'' menu.
2. Using the Map Module, interpolate the water surface elevations in the 1D Hyd Centerline and 1D Hyd Cross Section coverages. This can be done by selecting each coverage to make it active and then selecting '''Interpolate Water Surface Elevations''' from the ''River Tools'' menu.
#Go to the Terrain Data module and use ''Flood'' | '''Delineate''' to delineate the floodplain.
 
#In ''Display Options'', turn on the contours. Turning on color filled contours with transparency and a background image (a contour map or an aerial photograph) will help better visualize the flood extents.
3. Go to the Terrain Data module and Delineate the floodplain.
#If there are areas known to be interpolated incorrectly and are not flooded (see Figure 1), draw a polygon around these regions so the floodplain will not be delineated in these areas. Remove these areas from the floodplain delineation by creating a Flood Barrier coverage (see Figure 2 below) and then delineating the floodplain again using the ''User defined flood barrier coverage'' option (see Figure 3 below).
 
4. In ''Display Options'', turn on the contours. Turning on color filled contours with transparency and a background image (a contour map or an aerial photograph) will help you to better visualize the flood extents.
 
5. If there are areas you know are interpolated incorrectly and are not flooded (see Figure 1), you can draw a polygon around these regions so the floodplain will not be delineated in these areas. You can remove these areas from the floodplain delineation by creating a Flood Barrier coverage (see Figure 2 below) and then delineating the floodplain again using the User defined flood barrier coverage option (see Figure 3 below).
{{only in print|[[Image:image73.jpg|thumb|none|400 px|''Figure 1'']]}}
{{only in print|[[Image:image76.jpg|thumb|none|350 px|''Figure 2'']]}}
{|
|-
|{{hide in print|[[Image:image73.jpg|thumb|none|400 px|''Figure 1'']]}}
|{{hide in print|[[Image:image76.jpg|thumb|none|325 px|''Figure 2'']]}}
|}
 
[[Image:image89.jpg|thumb|none|400 px|''Figure 3'']]


<gallery mode="packed" heights="300px">
File:SMPDBK Floodplain Delineation1.jpg|''Figure 1'' &ndash; Areas known to be interpolated incorrectly and are not flooded.
File:SMPDBK Floodplain Delineation2.jpg|''Figure 2'' &ndash; A flood barrier coverage.
File:SMPDBK Floodplain Delineation3.jpg|''Figure 3'' &ndash; Floodplan Delineation dialog.
</gallery>


==Related Topics==
==Related Topics==
* [[WMS:SMPDBK|Simplified Dam-Break Analysis]]
* [[WMS:SMPDBK|Simplified Dam-Break Analysis]]
* [[WMS:Interpolating Hydraulic Model Results|Interpolate Results]]
* [[WMS:Interpolating Hydraulic Model Results|Interpolate Results]]
* [[WMS:Overview of Flood Plain Delineation|Flood Plain Delineation]]
* [[WMS:Overview of Floodplain Delineation|Floodplain Delineation]]
* [[WMS:SMPDBK Running a Simulation|Running a Simulation]]




{{WMSMain}}
{{WMSMain}}
[[Category:SMPDBK|P]]
[[Category:SMPDBK Dialogs|P]]
[[Category:Gallery]]

Latest revision as of 23:50, 12 December 2017

To view results of an SMPDBK analysis, perform the following steps:

  1. Run the simulation by selecting Run Simulation in the SMPDBK menu.
  2. Using the Map Module, interpolate the water surface elevations in the 1D Hyd Centerline and 1D Hyd Cross Section coverages. This can be done by selecting each coverage to make it active and then selecting Interpolate Water Surface Elevations from the River Tools menu.
  3. Go to the Terrain Data module and use Flood | Delineate to delineate the floodplain.
  4. In Display Options, turn on the contours. Turning on color filled contours with transparency and a background image (a contour map or an aerial photograph) will help better visualize the flood extents.
  5. If there are areas known to be interpolated incorrectly and are not flooded (see Figure 1), draw a polygon around these regions so the floodplain will not be delineated in these areas. Remove these areas from the floodplain delineation by creating a Flood Barrier coverage (see Figure 2 below) and then delineating the floodplain again using the User defined flood barrier coverage option (see Figure 3 below).
  • Figure 1 – Areas known to be interpolated incorrectly and are not flooded.

    Figure 1 – Areas known to be interpolated incorrectly and are not flooded.

  • Figure 2 – A flood barrier coverage.

    Figure 2 – A flood barrier coverage.

  • Figure 3 – Floodplan Delineation dialog.

    Figure 3 – Floodplan Delineation dialog.

Related Topics


v • e
WMS – Watershed Modeling System
Modules:Terrain Data  •   Drainage  •   Map  •   Hydrologic Modeling  •   River  •   GIS  •   2D Grid  •   2D ScatterWMS.PNG
Models:CE-QUAL-W2  •   GSSHA  •   HEC-1  •   HEC-HMS  •   HEC-RAS  •   HSPF  •   MODRAT  •   NSS  •   OC Hydrograph  •   OC Rational  •   Rational  •   River Tools  •   Storm Drain  •   SMPDBK  •   SWMM  •   TR-20  •   TR-55
Toolbars:Modules  •   Macros  •   Units   •   Digitize  •   Static Tools  •   Dynamic Tools  •   Drawing  •   Get Data Tools
Aquaveo
Retrieved from "https://www.xmswiki.com/index.php?title=WMS:SMPDBK_Post_Processing&oldid=133222"