GMS:Output Control: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
 
(3 intermediate revisions by the same user not shown)
Line 23: Line 23:
When using MODFLOW-USG Transport, the following options are available:
When using MODFLOW-USG Transport, the following options are available:
*'''USG-Transport Options''' – This button will bring up the ''USG-TRANSPORT Options'' dialog. This dialog has the following options:
*'''USG-Transport Options''' – This button will bring up the ''USG-TRANSPORT Options'' dialog. This dialog has the following options:
**''Use adaptive time stepping (ATSA)''
**''Use adaptive time stepping (ATSA)'' – Option to turn off or on adaptive time stepping. Select "Yes" to turn on.
**''Number of print times (NPTIMES)''
**''Number of print times (NPTIMES)'' – Specify the number of prints times if using adaptive time stepping. The print times can be entered using the '''USG-Transport Print Times''' button in the ''MODFLOW Output Control'' dialog.
**''Number of output steps (NPSTEPS)''
**''Number of output steps (NPSTEPS)'' – Enter the number of steps after which output is provided. When adaptive time stepping is used, the output control items that are otherwise provided for every time step are instead provided for every stress period.
**''Hot start stress period (ISPFAST)''
**''Hot start stress period (ISPFAST)'' – Enter a value for the stress period number to which to fast-forward.
**''Hot start time step (ITSFAST)''
**''Hot start time step (ITSFAST)'' – Enter a value for the time step number of ISPFAST value to which to fast-forward.
*'''USG-Transport Print Times''' – This button open a ''Table'' dialog where the times for the ''Number of print times (NPTIMES)'' can be entered.
*'''USG-Transport Print Times''' – This button open a ''Table'' dialog where the print times can be entered. The number of entries in the table are set by the ''Number of print times (NPTIMES)'' option in the ''USG-TRANSPORT Options'' dialog.




Latest revision as of 21:09, 17 March 2023

MODFLOW
Pre-processing
MODFLOW Commands
Building a MODFLOW Model
Map to MODFLOW
Calibration
Packages Supported in GMS
Saving a MODFLOW Simulation
Importing MODFLOW Files
Unsupported MODFLOW Features
Run MODFLOW
Post-processing
MODFLOW Display Options
MODFLOW Post-Processing Viewing Options
Reading a MODFLOW Simulation
Tutorials
Packages
Flow: BCF6, HUF, LPF, UPW
Solvers:

DE4, GMG, NWT, PCG,

PCGN, LMG, SIP, SOR,

SMS
Other:

BAS6, BFH, CHD1, CLN,

DRN1, DRT1, EVT1, ETS1,

GAGE, GHB1, GNC, HFB1,

HUF, LAK3, MNW1, MNW2,

OUT1, RCH1, RIV1, SFR2,

STR1, SUB1, SWI2, WEL1,

UZF1
v • e

The Output Control dialog is accessed from the MODFLOW menu. The Output Control dialog contains the following options:

Output Interval Options

The Output Interval section allows choosing which files to output and when to output the results. By default, GMS instructs MODFLOW to output heads and volume data to both data files and text output files. Drawdown is not output by default.

Other Output Options

Global Output File
Choose this option to use the global output file (*.glo). This file contains information about the input files and, during an inverse run using the PES process, will contain information about each iteration. Either the global file, list file, or both must be used with MODFLOW.
List Output File
Choose this option to use the list output file (*.out). This file contains information about the current MODFLOW run. This file will be overwritten during an inverse run using the PES process for each inverse iteration.
*.hff File For Transport
Select this option to output the head and flow file (*.hff) used by MT3DMS to generate the flow fields for transport modeling.
Enable saving of computed flows for all source/sink objects
This option allows GMS to create a flow observation for all sources/sinks that were created using the Map→MODFLOW command so that the user can see the computed flux through the group of boundary conditions. If the user is doing a transient simulation then having this option may cause MODFLOW to crash because MODFLOW attempts to allocate more memory than any of us have available. Turning off this option in this situation is the best course of action.
The MODFLOW Output Control dialog.

MODFLOW-USG Transport Options

When using MODFLOW-USG Transport, the following options are available:

  • USG-Transport Options – This button will bring up the USG-TRANSPORT Options dialog. This dialog has the following options:
    • Use adaptive time stepping (ATSA) – Option to turn off or on adaptive time stepping. Select "Yes" to turn on.
    • Number of print times (NPTIMES) – Specify the number of prints times if using adaptive time stepping. The print times can be entered using the USG-Transport Print Times button in the MODFLOW Output Control dialog.
    • Number of output steps (NPSTEPS) – Enter the number of steps after which output is provided. When adaptive time stepping is used, the output control items that are otherwise provided for every time step are instead provided for every stress period.
    • Hot start stress period (ISPFAST) – Enter a value for the stress period number to which to fast-forward.
    • Hot start time step (ITSFAST) – Enter a value for the time step number of ISPFAST value to which to fast-forward.
  • USG-Transport Print Times – This button open a Table dialog where the print times can be entered. The number of entries in the table are set by the Number of print times (NPTIMES) option in the USG-TRANSPORT Options dialog.


v • e
GMS – Groundwater Modeling System
Modules:2D Grid  •  2D Mesh  •  2D Scatter Point  •  3D Grid  •  3D Mesh  •  3D Scatter Point  •  Boreholes  •  GIS  •  Map  •  Solid  •  TINs  •  UGridsGMS Logo2.png
Models:FEFLOW  •  FEMWATER  •  HydroGeoSphere  •   MODAEM  •  MODFLOW  •  MODPATH  •  mod-PATH3DU  •  MT3DMS  •  MT3D-USGS  •  PEST  •  PHT3D  •  RT3D  •  SEAM3D  •  SEAWAT  •  SEEP2D  •  T-PROGS  •  ZONEBUDGET
Aquaveo
Retrieved from "https://www.xmswiki.com/index.php?title=GMS:Output_Control&oldid=158460"