GMS:DRT Package: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
No edit summary
Line 43: Line 43:
Care should be taken in entering [[GMS:Conductance|conductance]] in the conceptual model so that the [[GMS:Conductance|units are correct]].
Care should be taken in entering [[GMS:Conductance|conductance]] in the conceptual model so that the [[GMS:Conductance|units are correct]].


[[File:MODFLOW-DrainReturn.jpg|thumb|300 px|The ''MODFLOW Drain Return Package'' dialog.]]
==Drain Return package dialog==
==Drain Return package dialog==
The ''Drain Return package'' dialog allows the user to edit the location and the input values associated with each drain boundary condition. Drain boundary conditions cannot be created or deleted from this dialog. They can be created and deleted via the '''''Map → MODFLOW''''' command, or by using the [[GMS:MODFLOW Source/Sink Dialog|''MODFLOW Source/Sink'' Dialog]].
The ''Drain Return package'' dialog allows the user to edit the location and the input values associated with each drain boundary condition. Drain boundary conditions cannot be created or deleted from this dialog. They can be created and deleted via the '''''Map → MODFLOW''''' command, or by using the [[GMS:MODFLOW Source/Sink Dialog|''MODFLOW Source/Sink'' Dialog]].

Revision as of 18:40, 25 November 2013

MODFLOW
Pre-processing
MODFLOW Commands
Building a MODFLOW Model
Map to MODFLOW
Calibration
Packages Supported in GMS
Saving a MODFLOW Simulation
Importing MODFLOW Files
Unsupported MODFLOW Features
Run MODFLOW
Post-processing
MODFLOW Display Options
MODFLOW Post-Processing Viewing Options
Reading a MODFLOW Simulation
Tutorials
Packages
Flow: BCF6, HUF, LPF, UPW
Solvers:

DE4, GMG, NWT, PCG,

PCGN, LMG, SIP, SOR,

SMS
Other:

BAS6, BFH, CHD1, CLN,

DRN1, DRT1, EVT1, ETS1,

GAGE, GHB1, GNC, HFB1,

HUF, LAK3, MNW1, MNW2,

OUT1, RCH1, RIV1, SFR2,

STR1, SUB1, SWI2, WEL1,

UZF1
v • e

The Drain Return Package (DRT) is very similar to the regular Drain Package (DRN). Drains remove water from the aquifer as long as the water table is above the elevation of the drain. With the DRT package, some percentage of that removed water can be reintroduced to the aquifer at a specified grid cell.

DRT boundary conditions can be added to selected cells using the Point Sources/Sinks command in the MODFLOW menu. DRT objects can also be defined using the conceptual model approach in the map module.

Illustration of DRT package[1]

Conceptual model

Drains can be modeled using points, arcs and/or polygons in a conceptual model. The return cell cannot be specified in the conceptual model. This is because the conceptual model is independent of the grid and, in fact, there may be no grid at all when the conceptual model is defined. When GMS performs the Map→MODFLOW command, the return cell is always set to be the highest active cell above the drain cell. This can later be changed in the Drain package dialog.

The main DRT parameters and how they can be specified are given in the following table.

DRT Input Parameters
Parameter Points Nodes Arcs Polygons
Conductance YesY YesY YesY
Bottom elevation YesY YesY YesY
Rfprop (return-flow proportion) YesY YesY YesY

When specifying an arc as a DRT arc, the conductance and return flow factor are specified on the arc. Bottom elevation is specified at the nodes on the ends of the arc and is linearly interpolated along the length of the arc.

Care should be taken in entering conductance in the conceptual model so that the units are correct.

The MODFLOW Drain Return Package dialog.

Drain Return package dialog

The Drain Return package dialog allows the user to edit the location and the input values associated with each drain boundary condition. Drain boundary conditions cannot be created or deleted from this dialog. They can be created and deleted via the Map → MODFLOW command, or by using the MODFLOW Source/Sink Dialog.

The Use Return Flow toggle controls the existence of the "RETURNFLOW" optional keyword in the package input file.

Notes

  1. ^ Banta, Edward R. (2000), MODFLOW-2000, The U.S. Geological Survey Modular Ground-Water Model-Documentation of Packages for Simulating Evapotranspiration with a Segmented Function (ETS1) and Drains with Return Flow (DRT1). Open-File Report 00-466., Denver, Colorado, http://water.usgs.gov/nrp/gwsoftware/modflow2000/ofr00-466.pdf 
v • e
GMS – Groundwater Modeling System
Modules:2D Grid  •  2D Mesh  •  2D Scatter Point  •  3D Grid  •  3D Mesh  •  3D Scatter Point  •  Boreholes  •  GIS  •  Map  •  Solid  •  TINs  •  UGridsGMS Logo2.png
Models:FEFLOW  •  FEMWATER  •  HydroGeoSphere  •   MODAEM  •  MODFLOW  •  MODPATH  •  mod-PATH3DU  •  MT3DMS  •  MT3D-USGS  •  PEST  •  PHT3D  •  RT3D  •  SEAM3D  •  SEAWAT  •  SEEP2D  •  T-PROGS  •  ZONEBUDGET
Aquaveo
Retrieved from "https://www.xmswiki.com/index.php?title=GMS:DRT_Package&oldid=61462"