1. Create the sources/sinks coverage.
|
- Create a coverage with source/sink attributes.
1. Create new coverage from scratch.
|
- Use the New Coverage right-click command.
- Use the Coverage Setup dialog to create a new coverage by selecting the desired coverage properties and naming the coverage.
|
2. Create new coverage from an existing coverage.
|
- Use the Duplicate command on an existing coverage. This will copy any feature objects on the coverage.
- Use the Rename command to give the coverage a new name.
- Change the coverage setup.
|
|
2. Create source/sink feature objects.
|
- Create any of the source/sink object needed for the project. Not all source/sink objects are required.
1. Define head arcs or nodes.
|
1. Create head arcs or points.
|
- Create feature arcs or points in the head location. These are often created from existing boundary arcs.
1. Create feature points, arcs, nodes and vertices.
|
- In the map module, create feature objects in the active coverage.
- Use the Create Arc tool to create arcs in the map coverage.
- Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object.
- Double-click or press the Enter key to terminate the arc.
- Use the Create Point tool to create additional nodes alone or to split arcs.
|
2. Modify arcs.
|
- Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation.
1. Create additional vertices on arcs.
|
- Use the Create Vertex tool to add vertices along arcs.
|
3. Split arcs.
|
- An existing arc can be split by:
2. Add a node to the arc.
|
- Use the Create Point tool to add a node on an arc in order to split it into two arcs.
|
3. Connect the end of an existing arc to the middle of the arc.
|
- Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs.
|
4. Add a new connecting arc.
|
- Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs.
|
|
|
|
2. Add head properties.
|
- Using the Select Point/Node tool or Select Arc tool, right-click on the head arc or node and select the Attributes Table command.
- Define the head properties in the Attribute Table dialog. Heads can be specified or general.
|
|
2. Define drain arcs or nodes.
|
1. Create drain arcs or points.
|
- Create feature arcs or points in the drain location.
1. Create feature points, arcs, nodes and vertices.
|
- In the map module, create feature objects in the active coverage.
- Use the Create Arc tool to create arcs in the map coverage.
- Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object.
- Double-click or press the Enter key to terminate the arc.
- Use the Create Point tool to create additional nodes alone or to split arcs.
|
2. Modify arcs.
|
- Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation.
1. Create additional vertices on arcs.
|
- Use the Create Vertex tool to add vertices along arcs.
|
3. Split arcs.
|
- An existing arc can be split by:
2. Add a node to the arc.
|
- Use the Create Point tool to add a node on an arc in order to split it into two arcs.
|
3. Connect the end of an existing arc to the middle of the arc.
|
- Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs.
|
4. Add a new connecting arc.
|
- Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs.
|
|
|
|
2. Add drain properties.
|
- Using the Select Point/Node tool or Select Arc tool, right-click on the drain arc or node and select the Attributes Table command.
- Define the drain properties in the Attributes Table dialog.
|
|
3. Define wells.
|
1. Create wells points.
|
- Create feature points in the well location.
1. Create feature points, arcs, nodes and vertices.
|
- In the map module, create feature objects in the active coverage.
- Use the Create Arc tool to create arcs in the map coverage.
- Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object.
- Double-click or press the Enter key to terminate the arc.
- Use the Create Point tool to create additional nodes alone or to split arcs.
|
2. Modify arcs.
|
- Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation.
1. Create additional vertices on arcs.
|
- Use the Create Vertex tool to add vertices along arcs.
|
3. Split arcs.
|
- An existing arc can be split by:
2. Add a node to the arc.
|
- Use the Create Point tool to add a node on an arc in order to split it into two arcs.
|
3. Connect the end of an existing arc to the middle of the arc.
|
- Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs.
|
4. Add a new connecting arc.
|
- Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs.
|
|
|
|
2. Add well properties.
|
- Using the Select Point/Node tool, right-click on well nodes and select the Attributes Table command.
- Define the well properties in the Attributes Table dialog.
|
|
4. Define stream arcs.
|
1. Create stream arcs.
|
- Create feature arcs in the stream location.
1. Create feature points, arcs, nodes and vertices.
|
- In the map module, create feature objects in the active coverage.
- Use the Create Arc tool to create arcs in the map coverage.
- Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object.
- Double-click or press the Enter key to terminate the arc.
- Use the Create Point tool to create additional nodes alone or to split arcs.
|
2. Modify arcs.
|
- Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation.
1. Create additional vertices on arcs.
|
- Use the Create Vertex tool to add vertices along arcs.
|
3. Split arcs.
|
- An existing arc can be split by:
2. Add a node to the arc.
|
- Use the Create Point tool to add a node on an arc in order to split it into two arcs.
|
3. Connect the end of an existing arc to the middle of the arc.
|
- Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs.
|
4. Add a new connecting arc.
|
- Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs.
|
|
|
|
2. Add stream properties.
|
- Using the Select Arc tool, right-click on the stream arc and select the Attributes Table command.
- Define the stream properties in the Attributes Table dialog.
|
|
5. Define specified flow arcs.
|
1. Create specified flow arcs.
|
- Create feature arcs in the specified flow location.
1. Create feature points, arcs, nodes and vertices.
|
- In the map module, create feature objects in the active coverage.
- Use the Create Arc tool to create arcs in the map coverage.
- Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object.
- Double-click or press the Enter key to terminate the arc.
- Use the Create Point tool to create additional nodes alone or to split arcs.
|
2. Modify arcs.
|
- Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation.
1. Create additional vertices on arcs.
|
- Use the Create Vertex tool to add vertices along arcs.
|
3. Split arcs.
|
- An existing arc can be split by:
2. Add a node to the arc.
|
- Use the Create Point tool to add a node on an arc in order to split it into two arcs.
|
3. Connect the end of an existing arc to the middle of the arc.
|
- Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs.
|
4. Add a new connecting arc.
|
- Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs.
|
|
|
|
2. Add specified flow properties.
|
- Using the Select Arc tool, right-click on the specified flow arc and select the Attributes Table command.
- Define the specified flow properties in the Attributes Table dialog.
|
|
6. Define flow barrier arcs.
|
1. Create flow barrier arcs.
|
- Create feature arcs in the flow barrier location.
1. Create feature points, arcs, nodes and vertices.
|
- In the map module, create feature objects in the active coverage.
- Use the Create Arc tool to create arcs in the map coverage.
- Begin creating a new arc by clicking in the graphics window at either arc end. If clicking on an existing feature node, vertex or arc, the new arc will snap to that object.
- Double-click or press the Enter key to terminate the arc.
- Use the Create Point tool to create additional nodes alone or to split arcs.
|
2. Modify arcs.
|
- Feature arcs, whether digitized or incorporated from a boundary condition or a material coverage, often need to be edited after initial creation.
1. Create additional vertices on arcs.
|
- Use the Create Vertex tool to add vertices along arcs.
|
3. Split arcs.
|
- An existing arc can be split by:
2. Add a node to the arc.
|
- Use the Create Point tool to add a node on an arc in order to split it into two arcs.
|
3. Connect the end of an existing arc to the middle of the arc.
|
- Use the Select Points\Nodes tool to drag the node of an existing arc to anywhere in the middle of another arc. This will split the second arc into two arcs.
|
4. Add a new connecting arc.
|
- Use the Create Arc tool to start or end a new arc on an existing arc to split the existing arc into two arcs.
|
|
|
|
2. Add flow barrier properties.
|
- Using the Select Arc tool, right-click on the flow barrier arc and select the Attributes Table command.
- Define the barrier properties in the Attributes Table dialog.
|
|
|
|